MEN 01A201S12/5880-0009串行鏈路模塊,A201SR04說明書文檔
功能代碼55生成輸入/輸出模塊錯誤報告。這些問題報告為報告類型12。功能代碼55生成五種模塊問題報告錯誤類型（請參閱表6-2）。
?錯誤類型1-無響應/錯誤類型。
?錯誤類型2-校準錯誤。
?錯誤類型3-通道故障/超出范圍。
?錯誤類型9-輸入故障。
?錯誤類型12-輸出固定。
MEN 01A201S12/5880-0009串行鏈路模塊問題報告分為兩類：主要或致命錯誤和輕微或非致命錯誤。致命錯誤指示給定的操作模式將不起作用。致命錯誤生成錯誤類型為1、2或3的模塊問題報告。非致命錯誤表示模塊已發現錯誤，但將繼續運行。非致命錯誤生成錯誤類型為9和9的模塊問題報告12表6-2。功能代碼55模塊問題報告錯誤類型模塊錯誤糾正措施1-無響應/類型錯誤任何輸入/輸出擴展器總線通信故障。任何命令或數據校驗和失敗。錯誤也將由FC 55輸出N+9指示。檢查輸入/輸出擴展器總線分流，
拆下IMHSS03并重新插入。If錯誤遞歸，更換IMHSS03。硬件或D/A錯誤。錯誤也將由FC 55輸出N+8或N+6指示，分別地1、拆卸IMHSS03。插入模塊。如果錯誤再次出現，請更換模塊。2、可以通過運行隔離原因診斷。
Function code 55 generates I/O module error reports. These
problem reports are report type 12. Function code 55 generates five module problem report error types (refer to Table 6-2).
? Error type 1 - no response/wrong type.
? Error type 2 - calibration error.
? Error type 3 - channel failure/out of range.
? Error type 9 - input failure.
? Error type 12 - output fixed.
Problem reports are broken down into two categories: Major or
fatal errors, and minor or nonfatal errors. Fatal errors indicate
that the given mode of operation will not function. Fatal errors
generate module problem reports having error types one, twoor three. Nonfatal errors indicate that the module has discovered an error but will continue to function. Nonfatal errors
generate module problem reports having error types nine and
12.
Table 6-2. Function Code 55 Module Problem Report
Error Type Module Error Corrective Action
1 - No response/
wrong type
Any I/O expander bus communication failure.
Any command or data checksum failure. Error
will also be indicated by FC 55 output N+9.
Check I/O expander bus dipshunts,
remove IMHSS03 and reinsert. If error
recurs, replace IMHSS03.
Hardware or D/A error. Error will also be indicated by FC 55 output N+8 or N+6,
respectively.
1. Remove IMHSS03. Insert the module.
If the error recurs, replace the module.
2. Cause may be isolated by running
diagnostics.
