HONEYWELL 97197975-A01模塊,97197975-A01中文說明
將模塊插入MMU卡固定框架。
如果閥門在任何需求水平上振蕩，則拆除HSS將增益（雙列直插式開關S2）降低到下一個設置。例如，如果增益為13（極點4閉合），則更改增益至10（關閉5號桿，打開4號桿）。
8.將模塊插入MMU卡固定框架。
9.重復步驟1和2，檢查每個位置的閥門操作
需求水平。當該點為實現了閥門的平穩運行。
HONEYWELL 97197975-A01模塊10、記錄日期、時間、控制器增益設置和在空間pro中調整控制器的人員姓名見表B-1。在控制器調整中進行任何調整時，更新控制器調整日志。
注意：在功能失效之前，不要開始操作HSS模塊代碼150重置為0。如果模塊被損壞，校準周期可能開始重置，S3設置為1。
在線校準在以下情況下，可以使用功能代碼150進行在線校準：還有其他在線控制閥正在運行正確地這些閥門的HSS模塊將補償校準中閥門和致動器的重新定位。使用進行校準時，校準周期為35分鐘或更長時間在線校準。要進行在線校準，請參閱初始校準并執行伺服閥和的步驟致動器校準程序。
5. Insert the module in the MMU card cage.
6. Repeat Steps 1 through 3.
7. If the valve oscillates at any demand level, remove the HSS
module and lower the gain (dipswitch S2) to the next setting.
For example, if the gain is 13 (pole 4 is closed), change the gain
to 10 (close pole 5, open pole 4).
8. Insert the module in the MMU card cage.
9. Repeat Steps 1 and 2 to check valve operation at each
demand level. The controller gain is set when this point is
reached and smooth valve operation is obtained.
10. Record the date, time, controller gain setting and the
names of the personnel tuning the controller in the space pro
vided in Table B-1. Update the controller tuning log when mak
ing any adjustment in controller tuning.
NOTE: Do not start operating the HSS module until S3 of function
code 150 is reset to 0. A calibration cycle could start if the module is
reset and S3 is set to 1.
ON-LINE CALIBRATION
On-line calibration with function code 150 is possible when
there are other controlling valves on-line that are operating
properly. The HSS modules for those valves will compensate for
the repositioning of valve and actuator in calibration. Use a
calibration cycle time of 35 minutes or more when doing an
on-line calibration. To do an on-line calibration, refer to INI
TIAL CALIBRATION and do the steps of the servo valve and
actuator calibration procedure.
