A4H124-24TX交換機,A4H124-24TX英文說明設置包裹增益為了能夠在顯示器上顯示實際的卷筒紙張力，卷筒紙張力和必須確定稱重傳感器上測得的力。這個比率是一個稱為包裹增益的比例因子。包裹增益取決于紙幅在測量輥上的包裹角度和紙幅的方稱重傳感器。因此，包裹增益取決于實際安裝。這將提供：T（張力）=包裹增益??FR（稱重傳感器測量方向上的腹板張力力）有兩種方法可以確定腹板張力與負載上測得的力之間的比率單元格，
A4H124-24TX交換機通過懸掛重量或計算。帶懸掛重量（菜單懸掛重量）將一根繩索準確地沿著腹板路徑纏繞，并施加已知重量應用的已知重量模擬實際腹板張力和電子測量施加的重量對稱重傳感器產生的力。當腹板張力（T）和相應的測量力（FR）已知時張力電子裝置計算T/FR比，并將該值存儲為包裹增益。當卷筒張力應用于輥時，張力電子設備通過以下方式計算卷筒張力：將測得的稱重傳感器上的力乘以包裹增益。在掛重程序之后，可以通過張力電子裝置計算包裹增益可在EnterWrapGain菜單中找到按計算（菜單EnterWrapGain）包裹增益是一個比例因子，對應于腹板張力（T）和作用在稱重傳感器測量中的腹板張力的力分量（FR）方向包裹增益范圍為0.5-20。如果嘗試將包裹增益設置在此范圍之外，則顯示屏上將顯示消息“WrapGainTooLow”或“WrapGainTooHigh”。包裹增益可設置為分辨率0.01。描述包裹增益計算原理的示例：Set Wrap GainTo be able to present actual web tension on the display, the ratio between web tension andmeasured force on the load cell must be determined.This ratio is a scaling factor called Wrap Gain.The Wrap Gain depends on the web's wrap angle on the measuring roll and the orientation of theload cells. Therefore, Wrap Gain depends on the actual installation.This gives:T (tension) = Wrap Gain ??FR (force of web tension in load cell measuring direction)There are two ways to find out the ratio between web tension and measured force on the loadcells, by Hanging weights or by Calculation.? With hanging weights (Menu HangWeight)String a rope that follows the web path exactly and apply a known weight.The applied known weight simulates the actual web tension and the electronics measuresthe resulting force on the load cells caused by the applied weight.When both web tension (T) and the corresponding measured force (FR) are known thetension electronics calculates the ratio T / FR and stores the value as Wrap Gain.When web tension is applied to the roll the tension electronics calculates web tension bymultiplying the measured force on the load cells with the Wrap Gain.After the hanging weight procedure the wrap gain calculated by the tension electronics canbe found in the EnterWrapGain menu. ? By calculation (Menu EnterWrapGain)Wrap Gain is a scaling factor which corresponds to the ratio between Web Tension (T) andthe force component (FR) from web tension that is acting in the load cell measuringdirection.The Wrap Gain range is 0.5 - 20. If you try to set the wrap gain outside this range,
