PB3-VME-2-E控制器模塊，SST使用參數
本章提供了以下方面的說明：
? 打開設備包裝
? 準備硬件
? 安裝MVME187 RISC單板計算機請注意，MVME712X的硬件準備說明轉換模塊在各自的用戶手冊中提供模型請參閱隨附的用戶手冊MVME712X。
打開設備包裝注意：如果裝運紙箱在收到后損壞，請請求開包期間承運人代理人在場以及設備的檢查。將設備從裝運箱中取出。
PB3-VME-2-E控制器模塊請參閱裝箱單并確認所有物品均已存在。保存包裝設備儲存和重新裝運的材料。下表列出了您之前需要做的事情你可以使用這個板，在哪里可以找到你需要的信息執行每個步驟。請務必閱讀本章和所有注意事項
注意事項，并在您之前隨身攜帶相關文檔開始下表列出了您之前需要做的事情你可以使用這個板，在哪里可以找到你需要的信息執行每個步驟。請務必閱讀本章和所有注意事項注意事項，并在您之前隨身攜帶相關文檔開始本節包括：
? 安裝前修改硬件配置
? 檢查187Bug EPROM
? 出廠跳線設置
? 準備MVME187
? 準備系統機箱安裝前修改配置選擇所需配置并確保對于MVME187，可能需要進行某些選項修改安裝前。開關、跳線頭、接頭和LED的位置MVME187上的指示器如圖3-1所示。選項修改
MVME187規定了通過以下方式修改期權：
? 大多數選項的軟件控制
? 某些選項標題上的跳線設置
? most安裝后控制寄存器中的位設置其他選項–控制寄存器在單板中描述
計算機程序員參考指南，如相關本手冊第1章中的文件。
corresponding time arrives, it will be triggered respectively: the next tank of aggregate batching, feeding of cement, water and chemicals, lowering of hopper, start of mixing timer. When the cement feeding time arrives, close the unloading butterfly valve and trigger the next cement batching. When the feeding time of water and reagent arrives, close the solenoid valve, stop the booster pump and trigger the next filling and reagent batching. When the hopper drops to the lower limit, it will stop automatically and wait for the feeding of aggregate belt.
3. Mixing and unloading concrete: when the mixing time arrives, open the concrete unloading door and start the unloading timer. When the time arrives, it will be closed automatically, and the output data will be counted at the same time.
During operation: (vehicle capacity) the last tank of concrete batching is completed, the system is closed, the batching trigger is triggered, and batching is no longer required. After the unloading of the last tank of concrete is completed, the system disconnects the automatic operation contact and returns to the standby state.
Conclusion:
The system has the advantages of simple structure and convenient operation and maintenance. It is suitable for small concrete mixing plants on the construction site. However, it still has shortcomings. With the development of modern science and technology, electronic belt scale and liquid flowmeter have also been widely used. The introduction of new technology to further simplify the system structure, mechanical structure and metal structure is a new idea to improve the performance of equipment. After the machine is started, count every time a sealing and cutting action is completed. After the power is turned on, the counter is automatically cleared. 7) Stop positioning function: when the machine is stopped in any state, the heat seal body is in the open position to avoid scalding the packaging materials. 8) Automatic shutdown and alarm function: in case of paper break, no paper and bag jam, it will automatically stop and alarm. That is, when the packaging material breaks or the packaging material is used up (see Fig. 8 for paper breaking detection) and the packaging bag accumulates above the cutter (see Fig. 10 for bag jamming detection), the machine will automatically stop and give an alarm to prompt the operator to deal with it. Carefully understand the input and output equipment, check the location and name of the sensor and the relationship with the output equipment. 3) understand the safety protection measures and fault alarm in the control process. 4) prepare the program in line with the control process. 5) commissioning program. 5 Use logo! 6. No design circuit diagram / wiring diagram LOGO! Control program development 1) control program of main motor
The bag pulling motor of the particle packaging machine uses a stepping motor driver to control the bag pulling time and length. In the logo, there is no corresponding function block, so in the program I designed, the control of bag pulling motor needs to be improved. 2) Other control logos of this model of particle packaging machine can be basically realized. However, due to the large number of digital signal inputs required in the control process, more expansion blocks are required. This change will reduce the cost. 3) The particle packaging machine has strict requirements on the heating temperature of heat seal. Considering that the cost will be increased if the input quantity is continuously increased, and this model of packaging machine can be well realized through simple control, the input of analog quantity is not considered in this project.
