DS200TCCAG1BAA通用卡件,GE中文PDF說明書在線閱讀
配置交換機上的開關、連接器和LED指示燈的位置MVME197LE如圖2-1所示。MVME197LE已出廠已測試，出廠時附帶出廠開關設置，如中所述
以下章節。MVME197LE使用其所需和工廠安裝的調試監視器MVME197Bug（197Bug）以及這些工廠開關運行背景配置開關S1：一般信息開關S1由九個雙向開關段組成。以下內容
圖顯示了開關S1的出廠配置。位值為當開關斷開時，讀數為1，當開關斷開時，讀數為零打開（關閉）。開關S1的默認值如下所示。
DS200TCCAG1BAA通用卡件MVME197LE上的八條通用輸入線（GPI0-GPI7）可能
配置可選開關段S1-1至S1-8。這些開關可以在VMEchip2 LCSR中作為寄存器讀?。ㄔ?FFF40088處）。參考MVME197LE、MVME197DP和MVME197SP中的VMEchip2章節單板計算機GPI0線路狀態程序員參考指南通過GPI7。工廠配置為通用輸入線禁用（打開）。MVME197LE可以作為系統控制器。系統控制器通過配置可選開關段啟用或禁用功能S1-9。當MVME197LE是系統控制器時，SCON LED為已打開。VMEchip2可以配置為系統控制器，如下所示：如下圖所示。出廠配置使用系統控制器開關已啟用（關閉）。串行端口4可以配置為使用RTXC4和TRXC4信號線。MVME197LE上的開關段S6-1和S6-2將串行端口4配置為分別驅動或接收TRXC4和RTXC4。出廠配置為串行端口4設置為接收兩個信號（打開）。時鐘線的其余配置通過使用MVME712M轉換上的串行端口4時鐘配置選擇標頭單元參考MVME712M過渡模塊和P2適配器板該標題配置的用戶手冊。
Configuration Switches
The location of the switches, connectors, and LED indicators on the
MVME197LE is illustrated in Figure 2-1. The MVME197LE has been factory
tested and is shipped with factory switch settings that are described in the
following sections. The MVME197LE operates with its required and factoryinstalled Debug Monitor, MVME197Bug (197Bug), with these factory switch
setting.
Configuration Switch S1: General Information
Switch S1 is a bank of nine two-way switch segments. The following
illustration shows the factory configuration of switch S1. The bit values are
read as a one when the switch is OFF (open), and as a zero when the switch is
ON (closed). The default value for switch S1 is shown below.The eight General Purpose Input lines (GPI0-GPI7) on the MVME197LE may
be configured with selectable switch segments S1-1 through S1-8. These
switches can be read as a register (at $FFF40088) in the VMEchip2 LCSR. Refer
to the VMEchip2 chapter in the MVME197LE, MVME197DP, and MVME197SP
Single Board Computers Programmer’s Reference Guide for the status of lines GPI0
through GPI7. Factory configuration is with the general purposes input lines
disabled (open).The MVME197LE can be the system controller. The system controller
function is enabled or disabled by configuring selectable switch segment
S1-9. When the MVME197LE is the system controller, the SCON LED is
turned ON. The VMEchip2 may be configured as a system controller as
illustrated below. Factory configuration is with the system controller
switch enabled (closed).Serial port 4 can be configured to use clock signals provided by the RTXC4 and
TRXC4 signal lines. Switch segments S6-1 and S6-2 on the MVME197LE
configures serial port 4 to drive or receive TRXC4 and RTXC4, respectively.
Factory configuration is with serial port 4 set to receive both signals (open).
The remaining configuration of the clock lines is accomplished by using the
Serial Port 4 Clock Configuration Select header on the MVME712M transition
module. Refer to the MVME712M Transition Module and P2 Adapter Board
User’s Manual for configuration of that header.
