VIBRO 200-510-017-017工控產品,說明書
在通電的情況下插入或拆卸模塊可能會導致?lián)p壞至模塊組件。
在這種情況下，存在可能導致死亡的危險電壓設備搬運、測試和調整時要格外小心。
3.小心地將MVME2603/2604從其VMEbus卡插槽中卸下將其平放，使接頭P1和P2面向您。
避免接觸集成電路的區域；靜電放電會損壞這些電路。
VIBRO 200-510-017-017工控產品4、將RAM200夾層模塊放置在基板頂部。RAM200下側的接頭J9應連接將相應的接頭J7平穩地安裝在MVME2603/2604。圖1-18。在MVME2603/2604上放置RAM200
5.將四個短十字螺釘穿過拐角處的孔進入MVME2603/2604的對峙狀態。擰緊螺釘。
6.將MVME2603/2604組件重新安裝到其正確的卡槽中。是確保模塊正確安裝在背板連接器中。不要損壞或彎曲接頭針腳。
7.更換機箱或系統護蓋，將系統重新連接到交流或直流電源，并打開設備電源。
PMC模塊安裝PCI夾層卡（PMC）模塊安裝在RAM200旁邊MVME2603/2604基板頂部的夾層。安裝PMC模塊，參考圖1-19，并按以下步驟進行：圖1-19。MVME2603/2604上的PMC模塊放置5、將PMC模塊的邊緣連接器滑入前面板從后面打開并將PMC模塊放置在基座頂部板PMC模塊下側的四個接頭然后應與相應的連接器平滑連接（J11/12/13/14）在MVME2603/2604上。6.將兩個短Phillips螺釘穿過前部的孔PMC模塊的角落，進入MVME2603/2604。擰緊螺釘。7.將MVME2603/2604組件重新安裝到其正確的卡槽中。是確保模塊正確安裝在背板連接器中。不要損壞或彎曲接頭針腳。8.更換機箱或系統護蓋，將系統重新連接到交流或直流電源，并打開設備電源
Inserting or removing modules with power applied may result in damage
to module components.
!
Warning
Dangerous voltages, capable of causing death, are present in this
equipment. Use extreme caution when handling, testing, and adjusting.
3. Carefully remove the MVME2603/2604 from its VMEbus card slot
and lay it flat, with connectors P1 and P2 facing you.
!
Caution
Avoid touching areas of integrated circuitry; static discharge can damage
these circuits.
4. Place the RAM200 mezzanine module on top of the base board.
Connector J9 on the underside of the RAM200 should connect
smoothly with the corresponding connector J7 on the
MVME2603/2604.Figure 1-18. RAM200 Placement on MVME2603/2604
5. Insert the four short Phillips screws through the holes at the corners
of the RAM200, into the standoffs on the MVME2603/2604.
Tighten the screws.
6. Reinstall the MVME2603/2604 assembly in its proper card slot. Be
sure the module is well seated in the backplane connectors. Do not
damage or bend connector pins.
7. Replace the chassis or system cover(s), reconnect the system to the
AC or DC power source, and turn the equipment power on.
PMC Module Installation
PCI mezzanine card (PMC) modules mount beside the RAM200
mezzanine on top of the MVME2603/2604 base board. To install a PMC
module, refer to Figure 1-19 and proceed as follows:Figure 1-19. PMC Module Placement on MVME2603/2604
5. Slide the edge connector of the PMC module into the front panel
opening from behind and place the PMC module on top of the base
board. The four connectors on the underside of the PMC module
should then connect smoothly with the corresponding connectors
(J11/12/13/14) on the MVME2603/2604.
6. Insert the two short Phillips screws through the holes at the forward
corners of the PMC module, into the standoffs on the
MVME2603/2604. Tighten the screws.
7. Reinstall the MVME2603/2604 assembly in its proper card slot. Be
sure the module is well seated in the backplane connectors. Do not
damage or bend connector pins.
8. Replace the chassis or system cover(s), reconnect the system to the
AC or DC power source, and turn the equipment power on
