PR6423/010-010-CN前置傳感器,EPRO使用尺寸TCS基于擁有三至四個PCI擴展槽無源總線的緊湊型SBC，而SCS則基于擁有兩個PCI擴展槽的slim SBC MB總線。PCI擴展槽用于一至兩個基于DSP的數據采集和控制模塊。如今每個TCS都基于Windows(而后是QNX，RT-Linux)。一些應用程序在LabView或其他的語言如C上發展起來。 TCS的核心是具有LAN芯片及256MB內存的緊湊型中型尺寸低功率SBC JUKI-511P(GXLV/GX1-233/266/300 32-bit MMX 處理器)。它提供了緊湊型閃存卡(Type2)、EIDE接口和PS/2鍵盤/鼠標接口。
PR6423/010-010-CN前置傳感器,EPRO使用尺寸內置SVGA/LCD顯示控制器提供了1024*768的解決方案，并提供了音頻接口和TV-OUT功能。數據采集和控制模塊包括了DSP、14位ADC和12位DAC。信號調理電子器件用于滿足真實目標的需要。根據構造模型作為內部發生器，以14位ADC和12位DAC用于信號仿真為基礎使用16個輸入測量通道用于數據采集，此節點能夠配準周期信號并將其顯示在監視器上以供分析。外部發生器基于相似的具有高精確度DAC的compact SBC，而用于此發生器的節點則產生外部信號用于實現對真實數據文件的正確仿真或復雜目標信號的數學模型。 SCS的核心是基于兩個擴展槽的Compact MB，并作為管理控制點(SCS)通過10/100M以太網連接到SCS。SBS的尺寸為185*122mm，電源為5V(1.8A)。帶有SBC的輸入信號調理電子器件和儀器數據采集器及控制模塊嵌入到機架（chassis）中。 SCS節點中更復雜的信號的建模支持信號作為數據文件或真實目標數據的數學構造和在內部或外部發生器上的信號建模。SCS的核心基于低功率的slim PC MS-6215和Windows(或Linux)。作為SBC(MS-6351)的Micro LPX MB基于815芯片集和賽揚/奔騰3處理器(FC-PGA)。815芯片集集成了顯示高速緩沖SDRAM控制器(支持32位133MHZ SDRAM陣列用于3D圖形顯示)。SCS能夠用于自治模式或二次集成系統上。機架（chassis）用于MS-6351Micro LPX MB與用于TCS和適應硬盤、光驅、軟驅一樣，具有同樣的尺寸，它也支持LAN、VGA、USB、揚聲器、PS/2鼠標和鍵盤。 傳統的10/100M以太網和SCI模塊分別提供了弱相互作用和強相互作用。傳統網絡(10/100M以太網，F(xiàn)ireWire，USB)作為標準連接用于計算機中。串行總線(USB，F(xiàn)ireWire)用于高速I/O上?，F(xiàn)場總線的概念對于所有電子設備來說應該是透明的。對于時間要求不嚴格的應用場合，10/100M以太網(TCP/IP)是個提供弱相互作用(信息傳遞)的好選擇。leakage of power grid, so that the feeder switch is both reliable and safe. The electrical schematic diagram of mine flameproof vacuum feed switch is shown in Figure 3. 3.2.1 the principle diagram of the total leakage protection system based on additional DC detection additional DC power detection leakage protection is shown in Figure 3, which is mainly composed of three-phase reactor and synchronous transformer T3, zero sequence reactor and zero sequence transformer T2, filter circuit composed of resistance and capacitance, and DC power source. Detect the change of the insulation resistance of the power grid to the ground through the DC power supply attached to the RL channel of the module. When the DC voltage is constant, the measured resistance value changes. When the insulation resistance drops to the action value specified in Table 1, the PLC program call is interrupted for immediate output to make the relay act, and its normally open contact connects the shunt tripping coil of the feeder switch to trip the switch, so as to realize leakage protection, and visually display the resistance value to the ground through the LCD. The additional DC power detection leakage protection system has the advantages of comprehensive protection and no dead zone action, but it also has the disadvantages of non selective action and long action time. For 1140V level, the leakage action time of 1K is not more than 30ms. The selective leakage
