主營產品
PLC可編程控制器模塊，DCS卡件，ESD系統卡件，振動監測系統卡件，汽輪機控制系統模塊，燃?xì)獍l(fā)電機備件等，優勢品牌：Allen Bradley、BentlyNevada、ABB、Emerson Ovation、Honeywell DCS、Rockwell ICS Triplex、FOXBORO、Schneider PLC、GE Fanuc、Motorola、HIMA、TRICONEX、Prosoft等各種進口工業零部件
產品廣泛應用于冶金、石油天然氣、玻璃制造業、鋁業、石油化工、煤礦、造紙印刷、紡織印染、機械、電子制造、汽車制造、塑膠機械、電力、水利、水處理/環保、鍋爐供暖、能源、輸配電等等
3BSE038415R1模擬量輸入模塊
注意：對于欠阻抗啟動（“UZ”）：除了由參數“RLoad”和“angeload”，反向區域獨立于啟動器運行。對于過電流啟動（“OC”）：反向區僅在過電流時運行啟動程序（“Istart”）已啟動。
二進制輸入（“Ext Blk UZ”）阻止操作，無論反向區域的啟動模式。
信號輸出：Meas Bward。反向區的測量僅在
第一區激活，即“Meas Bward”信號在最遲在第二時間步結束時。時間步長（延遲）
每個激活距離區域的運行時間（參數“X”<>0）由參數“Delay”確定，該參數具有
設置范圍為0至10秒，步長為0.01。參數“延遲（4/OR）”也與邏輯相關，該邏輯確定
是否適用于4區或超范圍區，即“延遲（4）或”＜“延遲（2）”，適用于超范圍區域，否則進入?yún)^(qū)域4。
設定時間必須滿足以下關系：
延遲（1）＜延遲（2）＜延時（3）＜時滯（4）＜時延（Def），
延遲（或）<延遲（2）。
對多個距離繼電器的工作時間進行分級時最短評分時間不應小于斷路器操作時間加上150 ms（復位時間+測量系統操作時間+安全裕度）。
建議的定時器設置： 1區：通常瞬時。 2區：“延遲（2）”通常設置為繼電器和斷路器操作時間、滅弧時間、信號傳輸時間和公差余量，其等于
約0.25至0.5秒。公差包括：順序跳閘。
區域3:“延遲（3）”設置為大約2 x“延遲（2）”。
區域4:“延遲（4）”或“延遲（Def）”通常設置為至少4倍延遲（2）。
特殊情況下可能需要設置，這些設置會有很大偏差根據上述建議。
區域1到4的時間步長必須小于“延遲（Def）”。確定區（Def）
最終（或第五）區受相同參數的影響作為低阻抗起動器（即XA、XB、RA、RB、RLoad和角度負載）。
相應的時間步長由參數“延遲”定義(Def)。
Note that:
for underimpedance starting (‘UZ’):
With the exception of the load discrimination defined by the
parameters ‘RLoad’ and ‘AngleLoad’, the reverse zone
operates independently of the starters.
for overcurrent starting (‘OC’):
The reverse zone is only in operation when an overcurrent
starter (‘Istart’) has picked up.
the binary input (‘Ext Blk UZ’) blocks operation regardless of
the starter mode for the reverse zone.
Signal output: Meas Bward.
Measurement of the reverse zone only takes place while the
first zone is active, i.e. the ‘Meas Bward’ signal resets at the
latest at the end the second time step.Time steps
(Delay)
The operating time of every activated distance zone (parameter
‘X’ <> 0) is determined by the parameter ‘Delay’, which has a
setting range of 0 to 10 s in steps of 0.01. The parameter
‘Delay (4/OR)’ is also associated with a logic, which determines
whether it applies to Zone 4 or to the overreaching zone, i.e. if
‘Delay (4/OR)’ < ‘Delay (2)’, it applies to the overreaching zone,
otherwise to Zone 4.
The set times must satisfy the following relationships:
Delay (1) < Delay (2) < Delay (3) < Delay (4) < Delay(Def),
Delay (OR) < Delay (2).
When grading the operating times of several distance relays, the
minimum grading time should not be less than the sum of the
circuit-breaker operating time plus 150 ms (reset time + operating time of the measuring system + safety margin).
Recommended timer settings:
Zone 1: normally instantaneous.
Zone 2: 'Delay (2)’ is normally set to the sum of relay and
circuit-breaker operating times, arc extinction time, signal
transmission time and a tolerance margin, which amounts to
about 0.25 to 0.5 s. The tolerance includes an allowance for
sequential tripping.
Zone 3: 'Delay (3)’ is set to about 2 x ‘Delay (2)’.
Zone 4: 'Delay (4)’ or ‘Delay(Def)’ is normally set to at least
4 x ‘Delay (2)’.
Special cases may require settings, which deviate considerably
from the above recommendations.
The time steps of zones 1 to 4 must have settings less than
‘Delay(Def)’.Definitive zone
(Def)
The definitive (or fifth) zone is subject to the same parameters
as the underimpedance starters (i.e. XA, XB, RA, RB, RLoad
and AngleLoad).
The corresponding time step is defined by the parameter ‘Delay
(Def)’.
