主營產品
PLC可編程控制器模塊，DCS卡件，ESD系統卡件，振動監測系統卡件，汽輪機控制系統模塊，燃?xì)獍l(fā)電機備件等，優勢品牌：Allen Bradley、BentlyNevada、ABB、Emerson Ovation、Honeywell DCS、Rockwell ICS Triplex、FOXBORO、Schneider PLC、GE Fanuc、Motorola、HIMA、TRICONEX、Prosoft等各種進口工業零部件
產品廣泛應用于冶金、石油天然氣、玻璃制造業、鋁業、石油化工、煤礦、造紙印刷、紡織印染、機械、電子制造、汽車制造、塑膠機械、電力、水利、水處理/環保、鍋爐供暖、能源、輸配電等等
0745745Q熱電偶輸出卡件
跳閘命令的分配（見第5.5.4.3節。）
用于分配跳閘命令的參數分組如下：“CB命令”子菜單。
輸出信號的分配取決于單個或三相跳閘已設置（參數“跳閘模式”）。在里面
在三相跳閘的情況下，三個跳閘輸出為分配給相同的輔助跳閘繼電器。單相跳閘（“跳閘模式”設置為“1PhTrip”或“3PhTripDel3”）需要三個單獨的輔助跳閘繼電器，即保護必須
配備至少兩個316DB61/62型二進制I/O單元。3.5.31.12.信號（見第5.5.4.2節。）
將二進制輸出分配給輔助信號繼電器的參數分組在“信號”子菜單中。一些信號輸出鎖存，直到全距離保護
功能復位（即，直到“啟動R+S+T”復位，自動重合閘（自動重合閘）A、 應用
該功能可配置為單相或三相自動重合閘。該裝置可與三種保護功能（距離、縱向差動和電流）中的任何一種一起運行，并且內部或外部同步檢查功能。
然而，額外的標準FUPLA邏輯T142詳細說明在文件中，1KHF600220對于1?斷路器應用中的單相重合閘是必要的。B、 特征最多4次快速或慢速重合閘嘗試第一個循環，最多4個可單獨配置的單個和/或
三相重合閘嘗試
每個重合閘循環的獨立運行指示器寬死區時間設置范圍
控制同步檢查裝置旁路的規定，以及通過外部信號延長第一區域的死區時間
在以下過程中，對不斷變化的故障條件的明確響應：死區時間（不斷演變的故障）
邏輯1。第二。主保護（冗余），雙工主/從方案對信號名稱的注釋：專門用于冗余或雙工方案的I/O信號在其名稱中分別包括圖“2”和“3”。
屬于基本配置（1保護）的信號
功能和1自動重合閘功能）的名稱中不一定包含圖“1”。
參數說明：將軍朗納普定義運行函數的處理單元
Allocation of tripping commands
(see Section 5.5.4.3.)
The parameters for allocating tripping commands are grouped in
the ‘CB COMMANDS’ sub-menu.
The allocation of the output signals depends on whether single
or three-phase tripping has been set (parameter ‘TripMode'). In
the case of three-phase tripping, the three tripping outputs are
allocated to the same auxiliary tripping relay. Single-phase tripping ('TripMode’ set to ‘1PhTrip’ or ‘3PhTripDel3') requires three
separate auxiliary tripping relays, i.e. the protection has to be
equipped with at least two binary I/O units Type 316DB61/62.
3.5.31.12. Signals
(see Section 5.5.4.2.)
The parameters for allocating binary outputs to auxiliary signalling relays are grouped in the ‘SIGNALLING’ sub-menu.
Some signalling outputs latch until the entire distance protection
function resets (i.e. until ‘Start R+S+T’ resets,Auto-reclosure (Autoreclosure)
A. Application
The function can be configured for single or three-phase autoreclosure.
The unit can operate in conjunction with any of the three protection functions (distance, longitudinal differential and current) and
either an internal or external synchrocheck function.
However, an additional standard FUPLA logic T142 as detailed
in the document 1KHF600220 is necessary for single-phase reclosing in 1? breaker applications.
B. Features
up to 4 fast or slow reclosure attempts
first cycle with up to 4 individually configurable single and/or
three-phase reclosure attempts
independent operating indicators for each reclosure cycle
wide dead time setting range
provision to control bypassing of the synchrocheck unit and
extending the dead time for the first zone by external signals
clearly defined response to changing fault conditions during
the dead time (evolving faults)
Logic for 1st. and 2nd. main protection (redundant), duplex
and master/follower schemes Remarks on the signal designations:
The I/O signals specifically for redundant or duplex schemes include the figure ‘2’, respectively ‘3’ in their designations.
The signals belonging to the basic configuration (1 protection
function and 1 auto-reclosure function) do not necessarily include the figure ‘1’ in their designations.
Explanations of parameters:
GENERAL
RunOnCPU
defines the processing unit which runs the function
