TC512V1分布式模塊
每當頻道改變。然而，它僅在請求時向CPU提供數據。如果頻道是以快速重復率運行時，其狀態的變化可能比CPU所能請求的更快狀態數據。在這種情況下，CPU可能會丟失一些狀態值。
詳細通道狀態字的初始值為全零。詳細頻道狀態字在以下情況下重置為零： FIP總線控制器通電或重啟
CPU從停止轉換到運行信道中止COMREQ中止信道
示例：檢索命令塊的詳細通道狀態此示例檢索通道5的詳細通道狀態數據，并將其放置在
寄存器100-101。它將COMREQ狀態字返回到%R10。本章描述FIP總線控制器對網絡故障的正常記錄。它解釋了如何將網絡故障信息存儲在PLC的選定區域中以及如何禁止將某些網絡故障記錄到I/O故障表中。
網絡故障的正常記錄
網絡診斷通信請求
啟動網絡診斷
停止網絡診斷，正常記錄網絡故障
FIP總線控制器通常將兩種類型的網絡故障記錄到I/O故障表中：
I/O總線故障
如果FIP總線控制器失去冗余網絡中的一條總線，則I/O總線
記錄的故障類型為“本地?fù)p耗總線1”或“本地?fù)p耗母線2”。
如果FIP總線控制器失去冗余網絡中的兩條總線，或失去其中一條
只有單工網絡中的總線，I/O總線故障記錄為“全部丟失”類型通信”。
如果遠程I/O設備或通用設備失去冗余系統中的一條總線網絡，記錄“遠程丟失總線1”或“遠程”類型的I/O總線故障總線2的損耗”。在單工網絡中，不記錄I/O總線故障。（見損失/增加設備故障）。
B、 設備故障丟失/增加（網絡存在）
FIP總線控制器還記錄以下設備的丟失/添加（網絡存在）故障：
配置遠程I/O和通用設備。設備丟失/添加的日志記錄無法禁用故障。
對于遠程I/O設備，F(xiàn)IP總線控制器關閉后立即開始故障記錄
操作的對于通用設備，在以下情況下有大約30秒的時間延遲
FIP總線控制器工作。
The Bus Controller refreshes this data in its own memory every time the status of the
channel changes. However, it supplies the data to the CPU only on request. If the channel is
operating with a fast repetition rate, its status may change faster than the CPU can request
the status data. In that case, some status values may be missed by the CPU.
The initial value of the Detailed Channel Status words is all zeros. The Detailed Channel
Status Words are reset to zero when:
The FIP Bus Controller is powered up or restarted
The CPU transitions from STOP to RUN
A channel abort COMREQ aborts the channel
Example Retrieve Detailed Channel Status Command Block
This example retrieves detailed channel status data for channel 5 and places it in
Registers 100-101. It returns the COMREQ Status word to %R10 This chapter describes normal logging of network faults by the FIP Bus Controller. It explains how network fault information can also be stored in a selected area of PLC
memory, and how to disable logging certain network faults into the I/O fault table.
Normal logging of network faults
Network Diagnostic COMREQ
Start Network Diagnostic
Stop Network Diagnostic Normal Logging of Network Faults
The FIP Bus Controller normally logs two types of network faults to the I/O fault table:
A. I/O Bus Faults
If the FIP Bus Controller loses one of the busses in a redundant network, an I/O Bus
Fault is logged of the type “Local Loss Bus 1” or “Local Loss bus 2”.
If the FIP Bus Controller loses both busses in a redundant network or it loses the one
and only bus in a simplex network, an I/O Bus Fault is logged of the type “Loss All
Comm”.
If a remote I/O device or generic device loses one of the busses in a redundant
network, an I/O Bus Fault is logged of the type “Remote Loss Buss 1” or “Remote
Loss Bus 2”. In a simplex network, I/O Bus Faults are not logged. (See Loss/Addition of
Device Faults).
B. Loss/Addition of Device Faults (Network Presence)
The FIP Bus Controller also logs loss/addition of device (network presence) faults for
configured remote I/O and generic devices. This logging of loss/addition of device
faults cannot be disabled.
For remote I/O devices, fault logging starts immediately after the FIP Bus Controller is
operational. For generic devices, there is a time delay of approximately 30 seconds after
the FIP Bus Controller is operational.
