UNS0119A-Z,V1控制處理器
CPX 928是單插槽PLC CPU，即由MS-DOS編程和配置，或要執行的基于Windows的編程軟件機器、工藝和材料的實時控制處理系統。它與I/O通信機架安裝的智能選件模塊背板采用VME C.1標準格式。
支持的選項模塊包括LAN接口字母數字可編程協處理器模塊
用于IC660/661 I/O的顯示協處理器、總線控制器產品、通信模塊、I/O鏈路
接口和所有IC697系列的離散和模擬I/O模塊。用戶RAM存儲器
CPX928具有內置內存板，其中6MB電池支持的CMOS RAM存儲器，用于用戶數據（程序、配置和寄存器數據）存儲用戶閃存
CPX928具有256K的內置非易失性閃存用戶數據存儲器（程序、配置和寄存器數據）存儲。該閃存的使用是：
可選擇的閃存中的固件存儲
該CPU使用閃存存儲操作數據系統固件。這允許在不拆卸或更換模塊的情況下更新固件EPROM。操作系統固件已更新通過將PC兼容計算機連接到模塊的串行端口，并運行所包含的軟件使用固件升級套件。
操作、保護和模塊狀態此模塊的操作可由控制三位運行/停止開關或通過附帶的編程器和編程軟件。
可以鎖定程序和配置數據通過軟件密碼或通過記憶保護鑰匙開關。當鑰匙在受保護位置、程序和配置數據可以只能由并聯的編程器進行更改僅（至總線變送器模塊）。a的狀態CPU由上的七個綠色LED指示模塊前面。
The CPX 928 is a single slot PLC CPU that is
programmed and configured by MS-DOS or
Windows based programming software to perform
real time control of machines, processes and material
handling systems. It communicates with I/O and
smart option modules over the rack-mounted
backplane using the VME C.1 Standard format.
Supported option modules include LAN Interface
modules, Programmable Coprocessor, Alphanumeric
Display Coprocessor, Bus Controller for IC660/661 I/O
products, Communications modules, I/O Link
Interface, and all of the IC697 family of discrete and
analog I/O modules.User RAM Memory
The CPX928 has a built-in memory board with 6
Mbytes of battery-backed CMOS RAM memory for
user data (program, configuration, and register data)
storage.
User Flash Memory
The CPX928 has 256K of built-in, non-volatile flash
memory for user data (program, configuraton, and
register data) storage. Use of this flash memory is
optional.
Firmware Storage in Flash Memory
This CPU uses flash memory for storing the operating
system firmware. This allows firmware to be updated without disassembling the module or replacing
EPROMs. The operating system firmware is updated
by connecting a PC compatible computer to the module’s serial port and running the software included
with the firmware upgrade kit.
Operation, Protection, and Module Status
Operation of this module can be controlled by the
three-position RUN/STOP switch or remotely by an
attached programmer and programming software.
Program and configuration data can be locked
through software passwords or manually by the
memory protect keyswitch. When the key is in the
protected position, program and configuration data can
only be changed by a programmer connected parallel
only (to the Bus Transmitter module). The status of a
CPU is indicated by the seven green LEDs on the
front of the module.
