公司主營產品圖展示
產品優勢
1：國外專業的供貨渠道，具有價格優勢
2：產品質量保證，讓您售后無憂
3：全國快遞包郵
4：一對一服務
產品詳情介紹
DATX133工控卡件
短路或過載時的行為：如果輸出發生短路或過載頻道，相關頻道將作為開關晶體管的高溫反應。
在某些時間間隔內，模塊會嘗試打開頻道。在每次開關試驗之前，信號所有通道將中斷約20μs。
這也適用于那些不涉及過載或短路事件。
短路或過載消除后，相關通道可以立即重新運行。這個紅色LED“過載”熄滅。發送給主機的錯誤消息：如果發生短路或過載，錯誤消息連同錯誤代碼一起發送給主服務器4號。在每種情況下，信道0都被視為故障，獨立于真正涉及的渠道。錯誤消息保持至少5秒，甚至如果短路或過載已在時間更短。
有關診斷的更多信息，請參閱用作總線的中央單元和耦合器的說明大師。為了達到IP65防護等級，必須在電纜密封套處使用一定直徑的合適電纜
（總線、I/O連接器、電源電壓）：總線和I/O的電纜直徑為4.5毫米至6.5毫米，電源電壓為5毫米至10毫米
mm.總線電纜的電氣規格見CS31系統數據。預期用途二進制輸出模塊ICPO 08 H1是一個遠程模塊
在CS31系統總線上。它有16個二進制通道以下功能：外殼和終端系統符合IP65防護等級CS31總線從模塊到單元為此，模塊有兩條總線連接器作為總線輸入和總線輸出。每個輸出都有自己的連接器，因此可以單獨拔下。
24 V DC電源電壓通過以下方式連接模塊外殼內的螺旋式端子。輸出采用開關晶體管，額定負載能力為2A防過載和短路。模塊用螺釘安裝。有鉆孔可安裝在后壁或水平表面。
CS31系統總線連接是電氣隔離的來自其余模塊組件
該模塊提供診斷功能（參見章節“診斷和顯示”）。
顯示和連接模塊外殼1 8個黃色LED，用于顯示信號狀態
輸出2個LED“總線錯誤”、“過載”和“電源”
指示操作條件和錯誤（參見“診斷和顯示”部分）
3 CS31總線連接器（輸入）
4 CS31總線連接器（輸出）
5 8個輸出連接器
6個PG11電纜密封套，用于24 V DC電源7 24 V DC和PE的端子位于可拆卸的蓋子。可以從頂部進入模塊。用于設置模塊的DIL開關地址也在封面下面。
8標簽字段
9安裝鉆孔（另見“尺寸標注圖紙”）
Behaviour in case of short–circuit or overload:
If a short–circuit or an overload has occurred on an output
channel, the involved channel will be switched off as a
reaction on a high temperature of the switching transistor.
In certain intervals, the module then tries to switch on the
channel again. Before every switching–on trial, the signal
at all channels will be interrupted for a period of ca. 20 μs.
This is also valid for those channels which are not
involved in the overload or short–circuit event.
After the short–circuit or overload has been eliminated,
the involved channel can operate immediately again. The
red LED ”O(jiān)verload” goes out.
Error message to the master:
In case of a short–circuit or an overload, an error
message is sent to the master, along with the error code
No. 4. In each case, the channel No. 0 is given as faulty,
independent of the really involved channel. The error
message is kept up for a period of at least 5 seconds, even
if the short–circuit or overload has been remedied in a
shorter time.
Fur further information concerning diagnosis, see the
descriptions of the central units and couplers used as bus
masters.In order to meet the Degree of Protection IP65, suitable cables with certain diameters must be used at the cable glands
(bus, I/O connectors, supply voltage): cable diameters for bus and I/O 4.5 mm to 6.5 mm, for supply voltage 5 mm to 10
mm. The electrical specifications for the bus cables can be found under the CS31 system data.Intended purpose
The binary output module ICPO 08 H1 is a remote module
on the CS31 system bus. It has 16 binary channels with
the following features:
Housing and termination system according to IP65
degree of protection
The CS31 bus line is looped through from module to
module. For this purpose, the module has two bus
connectors as bus input and bus output.
Each output has its own connector and thus can be
unplugged individually.
The 24 V DC supply voltage is connected via
screw–type terminals inside the module housing.
The outputs employ switching transistors,
have a rated load capability of 2 A and are overload and short–circuit proof.
The module is mounted with screws. There are bore holesavailable for both mounting on a rear wall or on a horizontal surface.The CS31 system bus connection is electrically isolated
from remaining module components.
The module offers diagnosis functions (see chapter”Diagnosis and displays”).
Displays and connections atmodule housing
1 8 yellow LEDs for displaying the signal statuses of the outputs
2 LEDs ”Bus Error”, ”O(jiān)verload” and ”Supply”
indicating of operating conditions and errors (see
section ”Diagnosis and displays”)
3 CS31 bus connector (input)
4 CS31 bus connector (output)
5 8 connectors for the outputs
6 PG11 cable gland for the 24 V DC power supply
7 The terminals for 24 V DC and PE are located under
a removable cover. It is accessible from the top of
the module. The DIL switch for setting the module
address is also under the cover.
8 Labelling fields
9 Bore holes for mounting (see also ”Dimensioned
drawing” at the end of this description)
