公司主營產品圖展示
產品優勢
1：國外專業的供貨渠道，具有價格優勢
2：產品質量保證，讓您售后無憂
3：全國快遞包郵
4：一對一服務
產品詳情介紹
NXPP-06C適配器主板
CM-IWS。2用于監測在純IT交流系統中符合IEC 61557-8。
測量的是系統線路之間的絕緣電阻和系統接地。當?shù)陀诳烧{(diào)值時閾值，輸出繼電器切換到故障狀態
狀態使用CM-IWS。2疊加直流測量信號為用于測量。根據疊加的直流測量電壓及其合成電流
待測系統的絕緣電阻為計算特點：
–電源電壓24-240 V AC/DC
–輸出1 c/o（15-16/18），閉路原理可通過控制輸入配置故障存儲/閉鎖
–測試：正面按鈕或控制輸入（S1-S3）
–重置：正面按鈕或控制輸入（S2-S3）
–測量輸入L–PE，外部電壓高達400伏交流電
–測量范圍：1-100 kΩCM-IWS。1和CM-IWN。1個用于監測絕緣接地電阻符合IEC 61557-8IT交流或直流系統。測量的是絕緣電阻系統線路和系統接地之間。墜落時低于可調閾值時，輸出繼電器切換到故障狀態。使用CM-IWS。1和CM-IWN.1將脈動測量信號輸入系統監測并計算絕緣電阻。
特點：–電源電壓24-240 V AC/DC
–輸出1 c/o（15-16/18）
–閉路原理
–可通過控制輸入配置故障存儲/閉鎖
–測量電路中的斷線檢測
–測試：正面按鈕或控制輸入（S1-S3）
–重置：正面按鈕或控制輸入（S2-S3）
–測量輸入L–PE，外部電壓高達250 V AC和300 V DC
–測量范圍：1-100 kΩ
來自CM-IWS的脈動測量信號。1和CM-IWN公司。1根據絕緣改變其形式電阻和系統泄漏電容。從此處開始絕緣電阻的變化預測當預測絕緣電阻對應于在下一個測量周期中計算的絕緣電阻小于設定的閾值，輸出繼電器被激活或停用，具體取決于在設備配置上。此測量原理是也適用于對稱絕緣的檢測故障。
特點：
–電源電壓24-240 V AC/DC
–輸出1 x 2 c/o或2 x 1 c/o（15-16/18、25-26/28）
–開路或閉路原理可選
–可通過控制輸入配置故障存儲/閉鎖
–可配置非易失性故障存儲
–兩個閾值（預警）和最終關閉
可配置的
–可配置測量電路中的中斷線檢測
–測試：正面按鈕或控制輸入（S1-S3）
–重置：正面按鈕或控制輸入（S2-S3）
–測量輸入L–PE，外部電壓高達400 V AC和600 V DC
–測量范圍：1-100 kΩ，2-200 kΩ
-連接至電壓高達690 V AC和1000 V DC CM-IVN
The CM-IWS.2
is used to monitor insulation resistance in accordance with IEC 61557-8 in pure IT AC systems. Measured are insulation resistances between system lines and system earth. When falling below the adjustable threshold values, the output relays switch into the fault state. With CM-IWS.2 a superimposed DC measuring signal is used for measurement. From the superimposed DC measuring voltage and its resultant current the value of the insulation resistance of the system to be measured is calculated. Characteristics: – Supply voltage 24-240 V AC/DC – Output 1 c/o (15-16/18), closed circuit principle – Fault storage / latching configurable by control input – Test: front face button or control input (S1-S3) – Reset: front face button or control input (S2-S3) – Measuring input L – PE with external voltages up to 400 V AC – Measuring range: 1-100 kΩ
The CM-IWS.1 and CM-IWN.1
serve to monitor insulation resistance in accordance with IEC 61557-8 in unearthed IT AC or DC systems. Measured are insulation resistances between system lines and system earth. When falling below the adjustable threshold values, the output relays switch into the fault state. With CM-IWS.1 und CM-IWN.1 a pulsating measuring signal is fed into the system to be monitored and the insulation resistance calculated. Characteristics: – Supply voltage 24-240 V AC/DC – Output 1 c/o (15-16/18) – Closed circuit principle – Fault storage / latching configurable by control input – Broken wire detection in measuring circuit – Test: front face button or control input (S1-S3) – Reset: front face button or control input (S2-S3) – Measuring input L – PE with external voltages up to 250 V AC and 300 V DC – Measuring range: 1-100 kΩ
The pulsating measuring signal
from CM-IWS.1 and CM-IWN.1 alters its form in dependence of the insulation resistance and the system leakage capacitance. From this altered form the change in the insulation resistance is forecast. When the forecast insulation resistance corresponds to the insulation resistance calculated in the next measurement cycle and is smaller than the set threshold value, the output relays are activated or deactivated, depending on the device configuration. This measuring principle is also suitable for the detection of symmetrical insulation faults. Characteristics: – Supply voltage 24-240 V AC/DC – Output 1 x 2 c/o or 2 x 1 c/o (15-16/18, 25-26/28) – Open or closed circuit principle selectable – Fault storage / latching configurable by control input – Non volatile failure storage configurable – Two threshold values (pre-warning) and final switch off configurable – Interrupted wire detection in measuring circuit configurable – Test: front face button or control input (S1-S3) – Reset: front face button or control input (S2-S3) – Measuring input L – PE with external voltages up to 400 V AC and 600 V DC – Measuring range: 1-100 kΩ, 2-200 kΩ – Coupling unit for connection to systems with voltages up to 690 V AC and 1000 V DC CM-IVN
