公司主營產品圖展示
產品優勢
1：國外專業的供貨渠道，具有價格優勢
2：產品質量保證，讓您售后無憂
3：全國快遞包郵
4：一對一服務
產品詳情介紹
3BUS208796-001數字量輸入輸出卡
接地故障跳閘在隔離或高阻抗接地系統中，如果：?當前不存在其他故障?接地故障保護已啟用?GF抑制時間（參數75）已過期?GF電流等于或大于GF跳閘水平（參數73）的時間段大于GF跳脫延遲（參數74），則SMC Flex控制器跳閘并顯示接地故障（GF），鐵芯平衡電流傳感器通常用于檢測由絕緣擊穿或異物進入引起的低電平接地故障。檢測此類接地故障可用于中斷系統，以幫助防止進一步損壞，或提醒相關人員及時進行維護。SMC Flex控制器的接地故障檢測功能需要使用外部傳感器。外部傳感器允許您啟用接地故障跳閘、接地故障報警或兩者。對于5…480 A設備，建議使用Cat傳感器。用于1…5 A鐵芯平衡接地故障保護的825-CBCT鐵芯平衡電流互感器。對于625…1250 A設備，此處列出了推薦的傳感器，并提供5…25 A芯平衡接地故障保護。?制造商：Flex Core?描述：600V額定電流互感器?目錄號：126-252?CT比率：2500:5接地故障報警
在以下情況下，SMC Flex控制器指示接地故障報警：?當前不存在警告
?啟用接地故障報警
?GF抑制時間（參數75）已過期
?GF電流等于或大于Gnd Flt A Lvl（參數77）熱敏電阻/PTC保護SMC Flex控制器提供端子23和24，用于連接
正溫度系數（PTC）熱敏電阻傳感器。
PTC傳感器通常嵌入電機定子繞組中以監測電機繞組溫度當電機繞組溫度達到PTC傳感器的溫度時溫度額定值，PTC傳感器的電阻從低到高價值由于PTC傳感器對實際溫度作出反應，因此增強了電機可以提供保護以解決冷卻受阻等情況以及高環境溫度。熱敏電阻/PTC保護SMC Flex控器提供端子23和24，用于連接正溫度系數（PTC）熱敏電阻傳感器。PTC傳感器
通常嵌入電機定子繞組中以監測電機繞組
溫度當電機繞組溫度達到PTC傳感器的溫度時溫度額定值，PTC傳感器的電阻從低到高
價值由于PTC傳感器對實際溫度作出反應，因此增強了電機可以提供保護以解決冷卻受阻等情況
以及高環境溫度。在以下情況下，SMC Flex控制器跳閘并顯示PTC指示：
?目前不存在其他故障
?PTC保護已啟用端子23和24之間的電阻大于繼電器響應電阻或小于短路跳閘電阻。
過度啟動/小時SMC Flex控制器允許您對每個小時（最多99小時）。這有助于將重復啟動引起的電機壓力降至最低在短時間內。
Ground Fault Trip
The SMC Flex controller trips with a ground fault (GF) indication if: ? No other fault currently exists ? Ground fault protection is enabled ? GF Inhibit Time (Parameter 75) has expired ? GF Current is equal to or greater than the GF Trip Level (Parameter 73) for a time period greater than the GF Trip Delay (Parameter 74) In isolated or high impedance-grounded systems, core-balanced current sensors are typically used to detect low-level ground faults that are caused by insulation breakdowns or entry of foreign objects. Detection of such ground faults can be used to interrupt the system to help prevent further damage, or to alert the appropriate personnel to perform timely maintenance. The ground fault detection capabilities of the SMC Flex controller require the use of an external sensor. The external sensor lets you enable Ground Fault Trip, Ground Fault Alarm, or both. For 5…480 A devices, the recommended sensor is a Cat. No. 825-CBCT core balance current transformer for 1…5 A core-balanced ground fault protection. For 625…1250 A devices, the recommended sensor is listed here and provides 5…25 A core-balanced ground fault protection. ? Manufacturer: Flex-Core ? Description: 600V Rated Current Transformer ? Catalog Number: 126-252 ? CT Ratio:2500:5 Ground Fault Alarm The SMC Flex controller indicates a Ground Fault Alarm if: ? No warning currently exists ? Ground fault alarm is enabled ? GF Inhibit Time (Parameter 75) has expired ? GF Current is equal to or greater than the Gnd Flt A Lvl (Parameter 77)
Thermistor/PTC Protection
The SMC Flex controller provides terminals 23 and 24 for the connection of positive temperature coefficient (PTC) thermistor sensors. PTC sensors are commonly embedded in motor stator windings to monitor the motor winding temperature. When the motor winding temperature reaches the PTC sensor’s temperature rating, the PTC sensor’s resistance transitions from a low to high value. Because PTC sensors react to actual temperature, enhanced motor protection can be provided to address such conditions as obstructed cooling and high ambient temperatures.
The SMC Flex controller trips with a PTC indication if: ? No other fault currently exists ? PTC protection is enabled The resistance across terminals 23 and 24 is either greater than the relay’s response resistance or less than the short-circuit trip resistance. Excessive Starts/Hour The SMC Flex controller lets you program the allowed number of starts per hour (up to 99). This helps minimize motor stress caused by repeated starting over a short time period.
