公司主營產品圖展示
產品優勢
1：國外專業的供貨渠道，具有價格優勢
2：產品質量保證，讓您售后無憂
3：全國快遞包郵
4：一對一服務
產品詳情介紹
40PB3203A回路I/O板
超溫SMC Flex控制器使用參數119中的值來監控使用內部熱敏電阻測量SCR和旁路的溫度。當達到電源極的最高額定溫度，機組關閉禁止停機和重啟。
溫度過高可能表示通風不足、溫度過高環境溫度、過載或過度循環。溫度升高后如果降低到允許的水平，則可以清除故障。
打開大門門開路故障表明SCR點火不正確，通常是由在其中一個電源極上檢測到SCR門打開。在控制器關閉時，它總共嘗試啟動電機三次。線路故障
SMC Flex控制器持續監控線路狀況是否異常因素。啟動前保護包括：
?線路故障（帶相位指示）
-線路電壓損失
-缺少負載連接
-SCR短路
運行保護包括：?線路故障（無相位指示）
-線路電壓損失
-缺少負載連接
您可以打開或關閉反相保護。反相保護僅在預啟動時起作用。
測量
電源監測參數包括：
?三相電流（參數4、5和6）
?三相電壓（參數1、2和3）
?功率（kW）（參數7）
?用電量（千瓦時）（參數8）
?功率因數（參數11）
?電機熱容量使用（參數12）
?經過時間（參數9）
帶制動控制的智能電機制動、Accu Stop和慢速選項。
經過的時間和kWH值會自動保存到上的存儲器中斷電。
電機熱容量利用率由內置電子散熱片決定超載。當該值達到100%時，發生過載故障。
輸入/輸出SMC Flex控制器最多可接受兩個輸入和四個輸出通過網絡控制。這兩個輸入在端子16（選項輸入#1，參數132）和端子15（選項輸入#2，參數29）。對于這兩個輸入，參數設置見表26，表39和表40為鉆頭標識。
您可以通過以下方式對停止輸入進行編程，以滿足所需的停止功能使用這兩個端子作為輸入。
這四個輸出是Aux#1（參數107）、Aux#2（參數110）和Aux#3（參數108）和輔助#4（參數109）。所有輔助觸點均為可編程為表26中的功能。如果輸出編程為網絡或網絡NC，可以通過網絡見表40，它定義了邏輯命令字（控制）。表達串行接口端口（DPI）是作為標準提供的，它允許您連接SMC Flex控制器與公告20HIM LCD接口的連接模塊。
圖22-DPI位置您可以將兩個外圍設備連接到DPI。最大輸出功率通過DPI的電流為280 mA。
Overtemperature
The SMC Flex controller uses the value in Parameter 119 to monitor the temperature of the SCRs and Bypass by using internal thermistors. When the maximum rated temperature of the power poles is reached, the unit shuts down and restart is inhibited. An overtemperature condition can indicate inadequate ventilation, high ambient temperature, overloading, or excessive cycling. After the temperature is reduced to allowable levels, the fault can be cleared. Open Gate An open gate fault indicates that improper SCR firing, typically caused by an open SCR gate, has been detected on one of the power poles. Before the controller shuts down, it attempts to start the motor a total of three times. Line Faults The SMC Flex controller continually monitors line conditions for abnormal factors. Pre-start protection includes: ? Line Fault (with phase indication) - Line voltage loss - Missing load connection - Shorted SCR Running protection includes: ? Line Fault (no phase indication) - Line voltage loss - Missing load connection You can toggle Phase Reversal protection either On or Off. Phase Reversal protection is functional only at pre-start. Metering Power monitoring parameters include: ? Three-phase current (Parameters 4, 5, and 6) ? Three-phase voltage (Parameters 1, 2, and 3) ? Power in kW (Parameter 7) ? Power usage in kWH (Parameter 8) ? Power factor (Parameter 11) ? Motor thermal capacity usage (Parameter 12) ? Elapsed time (Parameter 9)
Voltage measurement
is not available during the braking operation of the Smart Motor Braking, Accu-Stop, and Slow Speed with Braking control options. The elapsed time and kWH values are automatically saved to memory on power down. Motor thermal capacity usage is determined by the built-in electronic thermal overload. An overload fault occurs when this value reaches 100%. I/O The SMC Flex controller can accept up to two inputs and four outputs that are controlled over a network. The two inputs are controlled at terminal 16 (Option Input #1, Parameter 132), and terminal 15 (Option Input #2, Parameter 29). For these two inputs, see Table 26 for the parameter settings and Table 39 and Table 40 for the bit identification. You can program the Stop Input to meet the desired stop functionality by using these two terminals as inputs. The four outputs are Aux #1 (Parameter 107), Aux #2 (Parameter 110), Aux #3 (Parameter 108), and Aux #4 (Parameter 109). All auxiliary contacts are programmable to the function found in Table 26. If the outputs are programmed to Network or Network NC, they can be controlled over a Network. See Table 40, which defines the Logic Command Word (Control). Communication A serial interface port (DPI) is provided as standard, which lets you connect the SMC Flex controller connection to the Bulletin 20-HIM LCD interface modules. Figure 22 - DPI Location You can connect two peripheral devices to the DPI. The maximum output current through the DPI is 280 mA.
