公司主營產品圖展示
產品優勢
1：國外專業的供貨渠道，具有價格優勢
2：產品質量保證，讓您售后無憂
3：全國快遞包郵
4：一對一服務
產品詳情介紹
87TS50R1214 GKWE驅動控制卡
額定625…1250 A的控制器額定電流為625…1250 A的控制器需要共同控制才能正常工作活動控制電源通過接線板連接到產品CP1，位于端子1和4。該單一連接點為控制器供電模塊、接觸器和風扇?？刂齐娫幢仨殲?10/120V AC或230/240V AC，僅50/60 Hz。至少800 VA的控制電源必修的?？刂齐娫匆蟀刂颇K（75 VA），旁路接觸器（最大526 VA）和風扇功率（150 VA）。
根據具體應用，附加控制電路變壓器可能需要VA容量。
控制額定功率為230/240V AC的裝置有一個欠壓繼電器安裝。2014年之前建造的機組可能在欠壓繼電器。如果有電位計，則必須對其進行設置根據圖36，2014年以后建造的機組可能不會電位計，因?yàn)樵O(shè)置在內部編程到欠壓繼電器，無需調整。本節涵蓋了您需要解決的一些注意事項，具體取決于在您的應用程序上。
保護模塊您應該安裝一個包含MOV（金屬）的保護模塊（見圖65氧化物變阻器），以保護SMC Flex電源組件免受電氣影響瞬態和/或電氣噪聲。您可以安裝額定電壓為200…600V的保護模塊控制器來保護來自電氣瞬變的功率元件。
保護模塊卡夾線路上產生的電壓瞬變
以防止此類浪涌損壞SCR。強烈建議使用MOV，因?yàn)?80V和600V MOV分別提供1400V和1600V的最大保護?？赡軙?huì)出現兩種情況，表明需要用于使用保護模塊。1.瞬態峰值-瞬態峰值通常會出現在線路上為SMC Flex控制器饋電或從SMC Flex饋電負載控制器。當設備帶有開路的載流電感。當觸點斷開電路。這些示例包括輕載電機、變壓器、螺線管、全電壓起動器和機電制動器。閃電也會導致尖峰。
2.快速上升的Wavefronts-如果SMC Flex控制器安裝在存在快速上升波前的系統，盡管不是可能需要高峰值電壓、保護模塊。閃電也會導致這種類型的響應。此外，如果控制器與其他SCR設備（如AC/DC）在同一總線上驅動器、感應加熱設備或焊接設備）、點火這些設備中的SCR可能會產生噪音
Controllers rated 625…1250 A
Controllers that are rated 625…1250 A require common control for proper operation. Control power is connected to the product through terminal block CP1, at terminals 1 and 4. This single connection point feeds the control module, contactors, and fans. Control power must be supplied as 110/120V AC or 230/240V AC, 50/60 Hz only. A control power source of at least 800 VA is required. The control power requirements include the control module (75 VA), bypass contactors (526 VA max), and fan power (150 VA). Depending on the specific application, additional control circuit transformer VA capacity may be required. Units with a control power rating of 230/240V AC have an undervoltage relay installed. Units built prior to 2014 may have potentiometers on the undervoltage relay. If potentiometers are present, you must set them according to Figure 36. Units built later than 2014 may not have potentiometers, because the settings are programmed internally to the undervoltage relay and no adjustment is required.
This section covers some considerations
that you need to address, depending on your application. Protective Modules You should install a protective module (see Figure 65) containing MOVs (Metal Oxide Varistors) to protect the SMC Flex power components from electrical transients and/or electrical noise. You can install protective modules controllers rated from 200…600V to protect the power components from electrical transients. The protective modules clip voltage transients that are generated on the lines to prevent such surges from damaging the SCRs. The use of MOVs is highly recommended, because 480V and 600V MOVs offer maximum protection of 1400V and 1600V, respectively.
There are two general situations that may occur that could indicate the need for using the protective modules. 1. Transient Spikes — Transient spikes will typically occur on the lines feeding the SMC Flex controller or feeding the load from the SMC Flex controller. Transient spikes are created on the line when devices are attached with current- carrying inductances that are open-circuited. The energy stored in the magnetic field is released when the contacts open the circuit. Examples of these include lightly loaded motors, transformers, solenoids, full voltage starters, and electromechanical brakes. Lightning can also cause spikes. 2. Fast-rising Wavefronts — If the SMC Flex controller is installed on a system that has fast-rising wavefronts present, although not necessarily high peak voltages, protective modules may be needed. Lightning can also cause this type of response. Additionally, if the controller is on the same bus as other SCR devices (such as AC/DC drives, induction heating equipment, or welding equipment), the firing of the SCRs in those devices can cause noise.
