公司主營產品圖展示
產品優勢
1：國外專業的供貨渠道，具有價格優勢
2：產品質量保證，讓您售后無憂
3：全國快遞包郵
4：一對一服務
公司主營產品文字介紹
PLC可編程控制器模塊，DCS卡件，ESD系統卡件，振動監測系統卡件，汽輪機控制系統模塊，燃?xì)獍l(fā)電機備件等，優勢品牌：Allen Bradley、BentlyNevada、ABB、Emerson Ovation、Honeywell DCS、Rockwell ICS Triplex、FOXBORO、Schneider PLC、GE Fanuc、Motorola、HIMA、TRICONEX、Prosoft等各種進口工業零部件、歐美進口模塊。
產品廣泛應用于冶金、石油天然氣、玻璃制造業、鋁業、石油化工、煤礦、造紙印刷、紡織印染、機械、電子制造、汽車制造、塑膠機械、電力、水利、水處理/環保、鍋爐供暖、能源、輸配電等等
產品詳情內容介紹
89NU03A-E驅動板
輸入選擇首先，找到模塊左側的四個檢修孔。這些孔允許訪問三個四位和一個五位DIP開關。
接下來，設置底部五位DIP開關的開關位置5（SW5模塊左側的檢修孔，用于選擇輸入范圍。此開關必須對應八位模塊配置DIP的開關位置8（SW8轉換SW5和SW8設置必須相同。
注：對于開關SW5，輸入范圍如下：z對于10 V（10 V或0-10 V），將SW5放置在左側。
z對于5 V（所有其他），將SW5放置在右側。有兩種方法可以配置模塊以接受當前輸入。有8個差動電流/電壓輸入模塊稱為B875-111。有16個單端電流/電壓輸入模塊稱為B877-111。B875-111現場連接為八個差動電流輸入配置B875-111時，請注意將接收這些輸入的通道。通過放置正極電壓輸入和電流之間的磁場連接器上的跳線相應通道的輸入端子。例如，如果通道2要接收電流輸入，必須在端子#7（CH2）和端子#6之間跳線電流輸入CH2），如下圖所示。
下圖顯示了B875的簡化示意圖–111模塊。B875–111模擬輸入模塊
電流輸入數據示例圖注：
DIP開關可訪問性在差速模式和應保留在出廠安裝的電壓輸入位置。
注：在以下情況下，可以同時存在電流和電壓輸入
條件：
z 1-5伏和4-20毫安
z 0-5 V和0-20 mA
z 5和20 mA將現場側接線連接至現場連接器上的適當引腳。電壓輸入不需要現場連接器上的跳線。請參閱顯示典型現場電路連接，見下文。注意：開路電壓輸入可能正或負漂移。如果需要開路檢測，應使用電流輸入。使用電壓時輸入，如果大值電阻器（2 MΩ或更大）放置在正極（+）和負極（-）輸入之間的現場連接器上。這個如果磁場連接斷開。電流輸入通過設置可通過側面訪問的DIP開關進行選擇用于接收輸入的每個通道的蓋子。DIP開關的精度為250Ω正極輸入和模擬回路之間的電阻。
位于左側的開關組4上的第五個開關（SW5）選擇電壓范圍此開關的位置必須與模塊配置的位置相同開關SW8，位于模塊后部。請參閱左側的標簽?zāi)K側面，以及下面顯示單端輸入（B877）的當前設置的圖示。單端輸入的電流設置，圖（B877）
Input Selection
First, locate the four access holes on the left side of the module. These holes allow access to three four-position and one five-position DIP switch. Next, set switch position 5 (SW5) of the five-position DIP switch found in the bottom access hole on the left side of the module, to select the input range. This switch must correspond to switch position 8 (SW8) of the eight-position module configuration DIP switch. SW5 and SW8 settings must be identical. NOTE: For switch SW5, the input ranges are as follows: z For 10 V (10 V or 0—10 V) place SW5 to the left. z For 5 V (all others) place SW5 to the right.There are two ways to configure the module to accept current inputs. With eight differential current/voltage inputs the module is called the B875-111. With sixteen single-ended current/voltage inputs the module is called the B877-111.
Connect field-side wiring to proper pins on the field connector. Voltage inputs do not require a jumper on the field connector. Refer to the illustration showing the typical field circuit connections, below. NOTE: Open-circuit voltage inputs may drift either positive or negatively. If opencircuit detection is required, a current input should be used. When using voltage inputs, an open circuit can be detected if a large-value resistor (2 MΩ or greater) is placed at the field connector across the positive (+) and negative (-) inputs. The resistor clamps the channel to a small offset voltage (<100 mV) if the field connections are broken.
B875-111 field connections
When configuring the B875-111 for eight differential current inputs, note the channels that will receive these inputs. Current inputs are selected by placing a jumper on the field connector between the positive voltage input and the current input terminal for the appropriate channel. For example, if channel 2 is to receive a current input, a jumper must be made between terminal #7 (CH2) and terminal #6 current input CH2), as shown on the following illustration. The following illustration represents the simplified schematic diagram for the B875– 111 module. B875–111 analog input module, current input dxample drawing NOTE: DIP switch accessibility DIP switches accessible through the side cover are not used in differential mode and should be left in the factory-installed voltage input positions. NOTE: Simultaneous current and voltage inputs can exist under the following conditions: z 1—5 V and 4—20 mA z 0—5 V and 0—20 mA z 5 and 20 mA
