公司主營產品圖展示
產品優勢
1：國外專業的供貨渠道，具有價格優勢
2：產品質量保證，讓您售后無憂
3：全國快遞包郵
4：一對一服務
公司主營產品文字介紹
PLC可編程控制器模塊，DCS卡件，ESD系統卡件，振動監測系統卡件，汽輪機控制系統模塊，燃?xì)獍l(fā)電機備件等，優勢品牌：Allen Bradley、BentlyNevada、ABB、Emerson Ovation、Honeywell DCS、Rockwell ICS Triplex、FOXBORO、Schneider PLC、GE Fanuc、Motorola、HIMA、TRICONEX、Prosoft等各種進口工業零部件、歐美進口模塊。
產品廣泛應用于冶金、石油天然氣、玻璃制造業、鋁業、石油化工、煤礦、造紙印刷、紡織印染、機械、電子制造、汽車制造、塑膠機械、電力、水利、水處理/環保、鍋爐供暖、能源、輸配電等等
產品詳情內容介紹
CPU86-NDP驅動處理器板
建議使用所示的屏蔽類型。信號源的一側可能使用雙絞線時，應連接至底盤接地。
注：通道獨立設置。電流、電壓、RTD、線性的任何混合物熱電偶或應變計/稱重傳感器可用作輸入。線性熱電偶（AS-5B47）注意指定接收線性熱電偶輸入的通道。線性的熱電偶輸入通過插入適當?shù)妮斎氚鼇?lái)選擇
頻道參考下圖，將現場側接線連接至適當?shù)默F(xiàn)場連接器上的針腳。
線性熱電偶輸入的典型現場電路連接，圖注：熱電偶必須是由AS-5B47輸入包正在使用中。冷端補償由溫度完成位于接頭塊正后方的傳感器。
注：建議使用所示的屏蔽類型。信號源的一側可能使用雙絞線時，應連接至底盤接地。
注：通道獨立設置。電流、電壓、RTD、線性的任何混合物熱電偶或應變計/稱重傳感器可用作輸入。注意指定接收應變計/稱重傳感器輸入的通道。拉緊通過插入合適的輸入包來選擇儀表/稱重傳感器輸入頻道參考下圖，將現場側接線連接至適當?shù)默F(xiàn)場連接器上的針腳。以下模塊的應變儀/稱重傳感器輸入快速啟動測試
快速啟動測試的典型現場電路連接描述如下：
z隔離電壓輸入（-10-+10 V）
z隔離電流輸入（4-20 mA）z隔離電壓輸入（-10-+10 mV）注意：此模塊在出廠時已在接頭上涂抹了nyogel潤滑脂確保接線板連接良好的針腳。不要清除此潤滑脂。
隔離電壓輸入（-10-+10 V）按照以下步驟配置模塊：八個通道（I/O圖中的B875）、AS–5B31006A隔離電壓輸入包和四個樣本平均值。模擬輸入模塊在出廠前進行校準。為了確保根據模塊精度，應每年定期校準微調罐。
校準可配置a/D輸入需要以下工具和材料模塊：z精度為0.0001 V、電壓為10 V的精密數字讀數伏特計
規模z一把1/8英寸的薄刃螺絲刀。
z一把1/4英寸十字螺絲刀。
注：不建議對模擬電流、低帶寬4進行校準-20 mA（AS–5B3201A）型輸入包，因?yàn)槠渚冉档徒o定通道的校準包括校準該通道的所有八個通道單元沒有校準特定通道的規定。因此，校準可以使用任何一個通道和任何類型的輸入包執行。校準可以需要校準信號通過輸入包。注：如果校準中使用的特定輸入包超出校準范圍，則使用此輸入包校準的B875模塊將不正確校準。
Linear Thermocouple (AS-5B47)
Note the channels designated to receive linear thermocouple inputs. Linear thermocouple inputs are selected by inserting the input pack for the appropriate channel. Refer to the diagram below and connect the field-side wiring to the proper pins on the field connector. Typical field circuit connections for linear thermocouple inputs, diagram NOTE: Thermocouple must be of the type designated by the dash number of the AS-5B47 input pack in use. Cold junction compensation is done by a temperature sensor located immediately behind the connector block. NOTE: The shield-type shown is recommended. One side of the signal source may be connected to chassis ground when using twisted pair wiring. NOTE: Channels are set independently. Any mixture of current, voltage, RTD, linear thermocouple, or strain gauge/load cell may be used as inputs.
The shield-type shown is recommended. One side of the signal source may be connected to chassis ground when using twisted pair wiring. NOTE: Channels are set independently. Any mixture of current, voltage, RTD, linear thermocouple, or strain gauge/load cell may be used as inputs.
Note the channels designated to receive strain gauge/load cell inputs. Strain gauge/load cell inputs are selected by inserting the input pack for the appropriate channel. Refer to the diagram below and connect the field-side wiring to the proper pins on the field connector. Typical field circuit connections for strain gauge/load cell inputs
Quick Start Tes
Quick start tests for the following modules are described below: z Isolated Voltage Input (-10 — +10 V) z Isolated Current Input (4 — 20 mA) z Isolated Voltage Input (-10 — +10 mV) NOTE: This module has had nyogel grease applied at the factory to the connector pins to ensure good terminal block connections. Do not remove this grease. Isolated Voltage Input (-10 — +10 V) Use the following procedure to configure the module as follows: eight channels (B875 in the I/O map), AS–5B31006A isolated voltage input pack, and four samples to be averaged.
The analog input module is calibrated at the factory prior to shipment. To ensure the module’s accuracy, the trim-pot should be calibrated regularly on a yearly interval. The following tools and materials are needed to calibrate a configurable A/D input module: z A precision digital readout voltmeter with an accuracy of 0.0001 V on a 10 V scale. z A 1/8-inch bit, thin-blade screwdriver. z A 1/4-inch Phillips-head screwdriver. NOTE: Calibration is not recommended for analog current, low bandwidth, 4— 20 mA (AS–5B32001A) type input packs because of their reduced accuracy Calibration of a given channel involves calibration of all eight channels of this module. There is no provision to calibrate a particular channel. Therefore, calibration can be performed with any one channel with any type of input pack. Calibration does require the calibration signals to pass through an input pack. NOTE: If the particular input pack used in calibration is out of calibration, then all B875 modules calibrated with this input pack will be improperly calibrated.
