公司主營產品圖展示
產品優勢
1：國外專業的供貨渠道，具有價格優勢
2：產品質量保證，讓您售后無憂
3：全國快遞包郵
4：一對一服務
公司主營產品文字介紹
PLC可編程控制器模塊，DCS卡件，ESD系統卡件，振動監測系統卡件，汽輪機控制系統模塊，燃?xì)獍l(fā)電機備件等，優勢品牌：Allen Bradley、BentlyNevada、ABB、Emerson Ovation、Honeywell DCS、Rockwell ICS Triplex、FOXBORO、Schneider PLC、GE Fanuc、Motorola、HIMA、TRICONEX、Prosoft等各種進口工業零部件、歐美進口模塊。
產品廣泛應用于冶金、石油天然氣、玻璃制造業、鋁業、石油化工、煤礦、造紙印刷、紡織印染、機械、電子制造、汽車制造、塑膠機械、電力、水利、水處理/環保、鍋爐供暖、能源、輸配電等等
產品詳情內容介紹
GNT0164000R0001驅動電源板
交換機設置兩個撥動開關位于模塊的左上角，用于確定與外部設備的通信類型。兩個開關都是用戶可選擇。
1.紙盒/BCD開關
此切換開關確定輸出數據是否由目標設備作為BCD或二進制值。
2.閃光燈激活高/低開關
此撥動開關允許為選通輸出數據選擇真高或真低。注：I/O映射選擇、BCD/二進制開關設置端子編號和輸出功能之間的關系用戶連接到標準螺釘端子排。剛性接線系統允許在不干擾接線的情況下插入或移除模塊。
下圖顯示了如何現場連接裝置。上拉電阻器連接必須在有源設備端安裝上拉電阻器才能使用B862輸出單元上拉電阻的值取決于連接到數據總線，如下所述。每個輸出滿足0.4 V邏輯低時最大16 mA，邏輯高時最小3.3 V。如果超過電流限制，應調整上拉電阻值在規范范圍內；否則，可能會獲得虛假結果。
下圖顯示了電阻器在設備上的連接方式
終止對于由16條數據線組成的單個設備，需要16個1k電阻，或，每個數據線一個1k電阻。隨著附加設備添加到數據總線上拉電阻的值必須增加1k。換句話說，如果兩個設備使用時，上拉電阻必須為2k，三個設備需要3k上拉，并且以此類推，對于每個數據，最多8個設備需要8k上拉線上拉電阻器連接此診斷測試以1/s的速度執行，所需時間少于1ms在診斷過程中，輸入無法檢測到低或高狀態，導致向控制器報告故障，活動LED閃爍。數字濾波對所有輸入執行，以減少滋擾性故障的發生。模塊和控制器之間的通信由四個字組成。二單詞包含每個輸入的狀態，另外兩個單詞包含故障每個輸入的狀態。在狀態字中，高或一表示打開條件。在故障狀態字中，一個高或一個表示相應輸入處存在故障。B863模塊不僅讀取24 Vdc輸入，還允許您監控通過使用輸入錯誤標志，檢查輸入電路的健康狀況。在以下方面例如，網絡允許您監視錯誤標志輸入以進行維護和故障排除。如果B863模塊的I/O映射為30001-30004，則寄存器30001和30002是真實世界的輸入，30003和3004成為錯誤標志輸入。
寄存器30003和30004與寄存器40011和40012的比較。
Switch Settings
Two toggle switches are located at the top left of the module and are used to determine the type of communication with external devices. Both switches are user selectable. 1. Bin/BCD Switch This toggle switch determines whether the output data is to be interpreted by the target devices as a BCD or a binary value. 2. Strobes Active Hi/Lo Switch This toggle switch allows selection of either true-hi or true-lo for strobing output data. NOTE: The relation between the I/O map selection, the BCD/binary switch setting Terminal Numbering and Output Functions User connections are made to a standard screw terminal strip. The rigid wiring system permits module insertion or removal without disturbing the wiring. The following illustration shows how to field connect the unit.The B863 module not only reads 24 Vdc inputs, but it allows you to monitor the health of the input circuits through the use of the input error flags. In the following example, networks allow you to monitor the error flag inputs for maintenance and troubleshooting. If the B863 module is I/O mapped as 30001-30004, then registers 30001 and 30002 are the real world inputs, and 30003 and 30004 become the error flag Inputs. Comparison of registers 30003 and 30004 to registers 40011 and 40012.
Pull-up Resistor Connection
Pull-up resistors must be installed at the active device end to use the B862 output module. The value of the pull-up resistor depends upon the number of devices that are attached to the data bus, as explained below. Each output meets 0.4 V maximum at 16 mA for a logic low and 3.3 V minimum at 16 mA for a logic high. If the current limit has been exceeded, the pull-up resistor values should be adjusted within specification; otherwise, spurious results may be obtained. The following illustration indicates how the resistors are connected at the device end. For a single device consisting of 16 data lines, 16 1 k resistors are required, or, one 1 k resistor per data line. As additional devices are added to the data bus, the value of the pull-up resistor must be increased by 1 k. In other words, if two devices are used, the pull-up resistor must be 2 k, three devices require a 3 k pull-up, and so on, with the maximum number of 8 devices requiring 8 k of pull-up for each data line. Pull-up resistor connection This diagnostic test is performed at a rate of 1/s, and takes less than 1 ms. The inability of an input to detect a low or high state during diagnostics, results in the reporting of a fault to the controller, and the flashing of the active LED. Digital filtering is performed on all inputs to reduce the occurrence of nuisance faults. Communication between the module and the controller consists of four words. Two words contain the state of each input, and the other two words contain the fault status of each input. Within the state words, a high, or one indicates a on condition. Within the fault status words, a high, or one indicates a fault at the respective input.
