產品內容介紹
A-B 80190-100-01-R光纖接口板
1.禁止驅動器連接或斷開通信卡控制器試圖通過它配置安全速度監視器模塊使用ADC。
2.將安全速度監視器模塊參數1[密碼]設置為模塊的當前密碼。
3.將安全速度監視器模塊參數5[鎖定狀態]設置為“0”（解鎖）。
4.將安全速度監視器模塊參數6[操作模式]設置為“0”（程序）。
5.如果安全速度監視器模塊的當前密碼不是“0”，則更改模塊的密碼設置為“0”
6.將安全速度監視器模塊參數1[密碼]設置為模塊的當前密碼。
7.將安全速度監視器模塊參數13[新密碼]設置為“0”
8.將安全速度監視器模塊參數17[密碼命令]設置為“1”（更改PW）。
9.取消禁止連接或重新連接電纜。
控制器可以下載新配置，包括新配置暗語安裝安全速度監視器模塊需要以下手動步驟進入運行模式，生成配置簽名，并鎖定配置。
更換安全速度監視器時，也需要執行這些步驟帶有新的“開箱即用”單元的模塊。
監測ADC進度ADC過程完成所需的時間從秒到秒不等
幾分鐘取決于幾個因素：
?為ADC啟用的外圍設備數量。
?如果驅動器/外圍設備的配置簽名指示需要為給定端口執行配置下載。
?Firmware Supervisor是否已啟用并需要升級驅動器和/或任何外圍設備。
?如果20-750-S1安全速度監視器選件模塊需要在其配置過程中使用手動“步驟”。
?如果使用DeviceLogix程序（端口14）。
啟用Firmware Supervisor后，啟動可能需要相當長的時間。
具有所有固件和參數都要更新，大約需要45…55分鐘。
可以使用HIM、驅動器軟件配置工具或通過HMI，可以觸發控制器程序的明確消息寫入。
為了滿足SIL CL3、PLe或Cat 4要求，用戶必須驗證安全速度監視器模塊中鎖定了正確的配置。
查看驅動器和安全速度監視器模塊文檔以了解更多信息。
作為配置過程的一部分，ADC可以自動重置驅動器。
這是因?yàn)槟承﹨?shù)需要重置才能生效。
如果是驅動器被替換為現成的驅動器，您通常會在中看到ADC過程中至少兩次復位，一次復位驅動器中的參數（端口0），對于PowerFlex 755驅動器，一個用于嵌入式EtherNet/IP適配器（端口13）。
Monitoring ADC Progress
The time it takes for the ADC process to complete will vary from seconds to several minutes depending on several factors: ? The number of peripherals enabled for ADC. ? If a configuration signature for the drive/peripheral indicates a configuration download needs to be performed for the given port. ? Whether Firmware Supervisor is enabled and needs to upgrade the drive and/or any peripherals. ? If a 20-750-S1 Safe Speed Monitor option module, which requires a manual ‘step’ in its configuration process, is used. ? If a DeviceLogix program (Port 14) is used. With the Firmware Supervisor enabled, startup can take quite a long time. With all firmware and parameters being updated, it takes approximately 45…55 minutes.1. Inhibit the drive’s connection—or disconnect the communication card through which the controller is trying to configure the Safe Speed Monitor Module using ADC. 2. Set Safe Speed Monitor Module parameter 1 [Password] to the Module’s current password. 3. Set Safe Speed Monitor Module parameter 5 [Lock State] to “0” (Unlock). 4. Set Safe Speed Monitor Module parameter 6 [Operating Mode] to “0” (Program). 5. If the Safe Speed Monitor Module’s current password is not “0,” change the password of the Module to “0.” 6. Set Safe Speed Monitor Module parameter 1 [Password] to the Module’s current password. 7. Set Safe Speed Monitor Module parameter 13 [New Password] to “0.”
These steps can be performed with a HIM
drive software configuration tool, or via an HMI that can trigger explicit message writes from the controller program. To meet SIL CL3, PLe, or Cat 4 requirements, the user must verify that the correct configuration is locked in the Safe Speed Monitor Module. See the drive and Safe Speed Monitor Module documentation for more information. 8. Set Safe Speed Monitor Module parameter 17 [Password Command] to “1” (Change PW). 9. Uninhibit the connection or reconnect the cable. The controller can download the new configuration, including the new password. The following manual steps are required to put the Safe Speed Monitor Module into Run mode, generate a configuration signature, and lock the configuration. These steps also need to be performed when replacing the Safe Speed Monitor Module with a new, “out of the box” unit.ADC can automatically reset the drive as part of the configuration process. This is done because some parameters require a reset before they take effect. If a drive is being replaced with an out-of-the-box drive, you will typically see at least two resets during the ADC process—one for the parameters in the drive (Port 0) and, for a PowerFlex 755 drive, one for the parameters in the embedded EtherNet/IP adapter (Port 13).
公司主營產品圖展示
產品優勢
1：國外專業的供貨渠道，具有價格優勢
2：產品質量保證，讓您售后無憂
3：全國快遞包郵
4：一對一服務
公司主營范圍簡介
PLC可編程控制器模塊，DCS卡件，ESD系統卡件，振動監測系統卡件，汽輪機控制系統模塊，燃?xì)獍l(fā)電機備件等，優勢品牌：Allen Bradley、BentlyNevada、ABB、Emerson Ovation、Honeywell DCS、Rockwell ICS Triplex、FOXBORO、Schneider PLC、GE Fanuc、Motorola、HIMA、TRICONEX、Prosoft等各種進口工業零部件、歐美進口模塊。
產品廣泛應用于冶金、石油天然氣、玻璃制造業、鋁業、石油化工、煤礦、造紙印刷、紡織印染、機械、電子制造、汽車制造、塑膠機械、電力、水利、水處理/環保、鍋爐供暖、能源、輸配電等等
