產品內容介紹
1391-DES45-DI數字交流伺服驅動器
保護I/O信號免受噪聲影響-布線時，將交流I/O信號線與直流I/O信號線隔離。如果這不可行，則為每組信號線使用集體屏蔽線布線時，將承載較大電流的信號線與其他信號線隔離。如果這不可行，則對承載大電流的信號線使用屏蔽線如果任何電感負載要連接到FA-M3的輸入或輸出端子，請?jiān)谪?fù)載附近安裝浪涌保護器或二極管。有關更多詳細信息，請參閱第A3.6.4小節“連接輸入設備”或第A3.6.5小節“連接輸出設備”中的“感應負載對策”。注意，當FA-M3在雷電頻率較高的地區使用時，請安裝保護設備，如電涌放電器重新檢查電源模塊的I/O規格。具體而言，請注意，將交流電源連接到需要直流輸入的電源模塊，并將200-240V交流電源連接至需要100-120V交流輸入的電源設備模塊，都會導致機器故障為避免觸電，接線前請關閉電源確保直流輸入電源模塊的“+”、“–”和FG端子以及交流輸入電源模塊中的L、N和FG接線端正確連接。端子螺釘和壓接端子F3PU-0S電源模塊使用M4螺釘接線板，而F3PU-0N電源模塊使用M3.5螺釘接線板。
接地程序
當FA-M3安裝到基本模塊上時，它會自動與基本模塊的金屬底盤接觸，因此它與控制器的信號電位和控制器的信號接地共用相同的電位。使用橫截面積超過2mm2的電線，通過盡可能短的路線連接到保護接地（符合每個國家的法規）。有關FA-M3接地線的詳細信息，請參閱第A3.3.2小節，與電源模塊內噪聲濾波器的中性端子相連。LG端子接地可適當衰減電源的共模噪聲。如果LG端子打開，噪聲濾波器的效果將降低。交流電源模塊需要保護接地。直流電源模塊需要保護接地或功能接地。當構建符合CE標記的系統時，將LG端子連接到FG端子，并使用編織線或其他電線將這些端子接地，以確保即使在高頻下也具有低阻抗。注意：當LG端子未連接到FG端子時，LG端子具有輸入電源電壓的一半電勢。重新檢查輸入/輸出模塊的I/O規格。請注意，施加超過輸入模塊最大允許輸入電壓或電流的電壓或電流，或施加超過輸出模塊最大開關容量的電壓或電壓或電流將導致機器故障、物理損壞或火災危險為避免觸電，接線前請關閉電源確保電源端子的極性正確。
Protecting I/O Signals against Noise
- Segregate the AC I/O signal lines from DC I/O signal lines when routing them. If this is not feasible, use collectively shielded lines for each group of these signal lines. - Segregate signal lines carrying larger current from other signal lines when routing them. If this is not feasible, use shielded lines for signal lines carrying large current. - If any inductive load is to be connected to an input or output terminal of the FA-M3, install a surge protector or a diode near the load. For further details, see “Inductive Load Countermeasures,” in subsection A3.6.4, “Connecting Input Devices” or “Inductive Load Countermeasures,” in subsection A3.6.5, “Connecting Output Devices.” CAUTION Install a protective device, such as a surge arrester, when the FA-M3 is to be used in a district with a high frequency of thunder.- Re-check the I/O specifications for the power supply module. Specifically, note that connecting an AC power supply to a power supply module requiring DC input and connecting a 200-240V AC power supply to a power supply module requiring 100- 120V AC input will lead to machine failure. - To avoid electrical shock, turn off the power before wiring. - Make sure that the ‘+’ , ‘–’ and FG terminals of a DC input power supply module and the L, N and FG terminals of an AC input power supply module are connected correctly.Terminal Screws and Crimp-on Terminals The F3PU??-0S power supply modules use M4-screw terminal blocks, unlike F3PU??-0N power supply modules, which use M3.5-screw terminal blocks.
Grounding Procedure
It is automatically brought into contact with the metal chassis of the base module when the FA-M3 is mounted onto the base module so it shares the same electric potential with the controller’s signal potential with the controller’s signal ground. Using a wire with a cross-section area of more than 2mm2 , connect to the Protective earth (Comply with the regulation of each country.) by taking the shortest route possible. For details onthe grounding lines of the FA-M3, see subsection A3.3.2, Is connected with the neutral terminal of the noise filter within the power supply module. Grounding the LG terminal properly attenuates the comon mode noise from the power supply. If the LG terminal is opened, the effect of the noise filter will be reduced.AC power supply module is required protective earth. DC power supply module is required protective earth or functional earth. When building a system compliant to CE Marking, connect LG terminal to FG terminal and ground these terminals with braided or other wires that ensure low impedance even at high frequencies. CAUTION LG terminal has a half potential of the input power supply voltage when LG terminal isn’t connected to FG terminal.Re-check the I/O specifications for the input/output modules. Note that applying a voltage or current that exceeds the maximum permissible input voltage or current of an input module or a voltage or current that exceeds the maximum switching capacity of an output module will lead to machine failure, physical damage or fire hazard. - To avoid electrical shock, turn off the power before wiring. - Make sure that the polarity of power terminals is correct.
公司主營產品圖展示
產品優勢
1：國外專業的供貨渠道，具有價格優勢
2：產品質量保證，讓您售后無憂
3：全國快遞包郵
4：一對一服務
公司主營范圍簡介
PLC可編程控制器模塊，DCS卡件，ESD系統卡件，振動監測系統卡件，汽輪機控制系統模塊，燃?xì)獍l(fā)電機備件等，優勢品牌：Allen Bradley、BentlyNevada、ABB、Emerson Ovation、Honeywell DCS、Rockwell ICS Triplex、FOXBORO、Schneider PLC、GE Fanuc、Motorola、HIMA、TRICONEX、Prosoft等各種進口工業零部件、歐美進口模塊。
產品廣泛應用于冶金、石油天然氣、玻璃制造業、鋁業、石油化工、煤礦、造紙印刷、紡織印染、機械、電子制造、汽車制造、塑膠機械、電力、水利、水處理/環保、鍋爐供暖、能源、輸配電等等
