產品內容介紹
369-HI-R-B-F-E-H-E綜合保護繼電器
系統設計下圖表示可以連接到面板的設備*1連接XBTZGI232時，COM端口的引腳9設置應為VCC*2使用隔離裝置的USB端口為其自身供電。無需設置單獨的電源*3參考附件（見第19頁）*4有關如何連接控制器和其他類型設備的信息，請參閱屏幕編輯軟件的相應設備驅動程序手冊*5有關支持的型號，請聯系您當?shù)氐氖┠偷码姎庵С执?6 HMIGTO1300和HMIGTO2300沒有以太網接口*7 HMIGTO1300/1310和HMIGTO2300沒有SD卡接口。在RS-422模式下使用RS-232C隔離單元或RS-485隔離單元時使用。（當隔離裝置將面板串行接口（D-sub 9針插頭）的輸出與RS-422接線板連接時）。將RS-232C隔離裝置與接線盒轉換適配器連接時需要轉換適配器。（當隔離裝置將可選RS-422通信項目連接至面板的COM1端口時）。將RS-485隔離裝置與接線盒轉換適配器連接時需要轉換適配器。（當隔離裝置將可選RS-485通信項目連接到面板的COM2端口時）。用于將屏幕數據從PC（USB類型a）傳輸?shù)矫姘澹║SB mini-B）的電纜。連接到操作面板正面的USB（mini-B）接口的延長電纜。符合USB2.0（A型）x 1。電源電壓：5 Vdc+/-5%。輸出電流：500 mA或以下。最大通信距離：5米（16.4英尺）。
結構規范
*1安裝在實心面板中的HMIGTO正面已使用與規范中所示標準等效的條件進行測試。盡管HMIGTO的阻力水平與這些標準相當，但對HMIGTO沒有影響的油可能會損害面板。這可能發生在存在汽化油的區域，或允許低粘度切削油長時間粘附在面板上的區域。如果面板正面保護板脫落，這些情況可能導致油進入面板，建議采取單獨的保護措施。此外，如果存在未經批準的機油，它們可能會導致前面板塑料罩變形或腐蝕。因此，在安裝面板之前，請確保確認面板操作環境中存在的條件類型。如果長期使用安裝墊片，或者如果面板及其墊片從面板上拆下，則無法保持原有的防護等級。為了保持原有的保護水平，請確保定期更換安裝墊片*2對于尺寸公差，所有+1/-0 mm（+0.04/-0 in）和R（角度）均低于R3（R0.12 in）*3即使安裝壁厚在“面板切割尺寸”的建議范圍內，取決于壁的材料、尺寸和面板和其他設備的安裝位置，安裝壁也可能翹曲。為了防止翹曲，可能需要加強安裝表面。安裝在實心面板中的面板正面已在與規范所示標準相當?shù)臈l件下進行了測試。
System Design
The following diagrams represent equipment you can connect to the panel. *1 When connecting the XBTZGI232, the COM port's pin 9 setting should be VCC. *2 Use the Isolation Unit’s USB port to supply power to itself. There is no need to set up a separate power supply. *3 Refer to Accessories (see page 19). *4 For information on how to connect controllers and other types of equipment, refer to the corresponding device driver manual of your screen editing software. *5 For supported models, contact your local Schneider Electric support representative. *6 The HMIGTO1300 and HMIGTO2300 do not have an Ethernet interface. *7 The HMIGTO1300/1310 and HMIGTO2300 do not have a SD card interface.To be used when using RS-232C isolation unit in RS-422 mode or RS-485 isolation unit. (When the isolation unit connects output from a serial interface of the panel (D-sub 9-pin plug) with an RS-422 terminal block).Conversion adapter required when connecting RS-232C isolation unit with terminal block conversion adapter. (When the isolation unit connects optional RS-422 communication items to COM1 port of the panel).Conversion adapter required when connecting RS-485 isolation unit with terminal block conversion adapter. (When the isolation unit connects optional RS-485 communication items to COM2 port of the panel).Cable for transferring screen data from a PC (USB Type A) to the panel (USB mini-B).Extension cable that attaches to the USB (mini-B) interface on the front side of the operation panel.Conforms to USB2.0 (Type A) x 1. Power supply voltage: 5 Vdc+/-5%. Output Current: 500 mA or less. Maximum communication distance: 5 m (16.4 ft).
Structural Specifications
*1 The front face of the HMIGTO, installed in a solid panel, has been tested using conditions equivalent to the standards shown in the specification. Even though the HMIGTO's level of resistance is equivalent to these standards, oils that should have no effect on the HMIGTO can possibly harm the panel. This can occur in areas where either vaporized oils are present, or where low viscosity cutting oils are allowed to adhere to the panel for long periods of time. If the panel's front face protection sheet peels off, these conditions can lead to the ingress of oil into the panel and separate protection measures are suggested. Also, if non-approved oils are present, they may cause deformation or corrosion of the front panel's plastic cover. Therefore, prior to installing the panel, be sure to confirm the type of conditions that will be present in the panel's operating environment. If the installation gasket is used for a long period of time, or if the panel and its gasket are removed from the panel, the original level of protection cannot be kept. To maintain the original protection level, be sure to replace the installation gasket regularly. *2 For dimensional tolerance, everything +1/-0 mm (+0.04/-0 in), and R in angle are below R3 (R0.12 in) *3 Even if the installation wall thickness is within the recommended range for the “Panel Cut Dimensions”, depending on wall’s material, size, and installation location of the panel and other devices, the installation wall could warp. To prevent warping, the installation surface may need to be strengthened. The front face of the panel, installed in a solid panel, has been tested using conditions equivalent to the standards shown in the specification.
公司主營產品圖展示
產品優勢
1：國外專業的供貨渠道，具有價格優勢
2：產品質量保證，讓您售后無憂
3：全國快遞包郵
4：一對一服務
公司主營范圍簡介
PLC可編程控制器模塊，DCS卡件，ESD系統卡件，振動監測系統卡件，汽輪機控制系統模塊，燃氣發電機備件等，優勢品牌：Allen Bradley、BentlyNevada、ABB、Emerson Ovation、Honeywell DCS、Rockwell ICS Triplex、FOXBORO、Schneider PLC、GE Fanuc、Motorola、HIMA、TRICONEX、Prosoft等各種進口工業零部件、歐美進口模塊。
產品廣泛應用于冶金、石油天然氣、玻璃制造業、鋁業、石油化工、煤礦、造紙印刷、紡織印染、機械、電子制造、汽車制造、塑膠機械、電力、水利、水處理/環保、鍋爐供暖、能源、輸配電等等
