330106-05-30-05-02-05 AI接線端子板
外部調制解調器機架
接口模塊直接支持以下外部調制解調器：無Hayes Ultra 9600 Hayes Optima 9600 Motorola FasTalkII 9600自定義初始化字符串設置和啟動調制解調器的命令。如果從列表中選擇調制解調器，默認初始化字符串將顯示在此字段中。如果選擇“自定義”，請根據調制解調器文檔中的信息輸入初始化字符串。字節超時在通信被認為完成之前，通信線路必須空閑的字節次數。一字節時間是所選波特率的函數。值的范圍為3至255。靜態數據注意事項每個靜態數據端口可以訪問3500機架中的六個監視器插槽。3500機架中的每個監視器插槽限制為32個PPL。動態信號選項標識哪些監視器向數據管理器I/O模塊上的動態連接器提供動態數據。該字段定義3500機架如何向通信處理器（TDIX或DDIX）提供機械數據。下表顯示了可用的不同選項。請記住以下幾點：?動態端口2始終分配給插槽8到13。?如果插槽包含監視器以外的其他內容，則不會返回該插槽的數據。?安裝在插槽14和15中的模塊無法返回任何數據。3配置信息3500/20操作和維護10動態信號選項監視器分配給數據管理器端口插槽2-7分配給數據Manager端口1機架類型：通信處理器的標準數量：2插槽14和14不能返回任何數據，因?yàn)槊總€(gè)TDIX和DDIX只能連接到最大值24個頻道。
機架類型
插槽2、4、6、8、10、12分配給Data Manager端口1機架類型：通信處理器的標準數量：1當機架設置有多個監視器/繼電器對時，使用此選項。分配給數據管理器端口1的插槽2、5、8、11機架類型：TMR，通信處理器的總線中繼數：1如果從插槽2、6、8或11中移除了監視器，則不會從該監視器組向通信處理器返回任何數據。監視器組插槽2、6、10分配給數據管理器端口1機架類型：TMR，帶單獨繼電器通信處理器數量：1如果從插槽2、8或10中移除監視器，則不會從該監視器組向通信處理器返回任何數據。監視器組圖例監視器分配給Data Manager端口1監視器分配給數據Manager端口2
External Modem Rack
The interface module directly supports the following external modems: no Hayes Ultra 9600 Hayes Optima 9600 Motorola FasTalkII 9600 custom initialization string settings and the command to start the modem. If you select a modem from the list, the default initialization string appears in this field. If you select Custom, enter the initialization string according to the information in the modem documentation. Byte timeout The number of bytes that the communication line must be idle before communication is considered complete. One byte time is a function of the selected baud rate. Values range from 3 to 255. Static Data Considerations Each static data port has access to six monitor slots in the 3500 rack. Each monitor slot in the 3500 rack is limited to 32 PPLs. The Dynamic Signal option identifies which monitors provide dynamic data to the dynamic connector on the Data Manager I/O module. This field defines how the 3500 rack provides mechanical data to the communication processor (TDIX or DDIX). The following table shows the different options available. Remember the following: ? Dynamic port 2 is always assigned to slots 8 through 13. ? If a slot contains something other than a monitor, the data for that slot will not be returned. ? Modules installed in slots 14 and 15 cannot return any data. 3 Configuration Information 3500/20 Operation and Maintenance 10 Dynamic Signal Option Monitor Assigned to Data Manager Port Slots 2-7 Assigned to Data Manager Port 1 Rack Type: Standard Number of Communication Processors: 2 Slots 14 and 14 cannot return any data because each TDIX and DDIX can only be connected to a maximum of 24 channels.
rack type
Slots 2, 4, 6, 8, 10, 12 are assigned to Data Manager Port 1 Rack Type: Standard Number of Communication Processors: 1 Use this option when the rack is configured with multiple monitor/relay pairs. Slot 2, 5, 8, 11 assigned to data manager port 1 Rack type: TMR, number of bus trunks for communication processor: 1 If a monitor is removed from slot 2, 6, 8, or 11, no data is returned from that monitor group to the communication processor. Monitor group slots 2, 6, and 10 are assigned to Data Manager Port 1 Rack Type: TMR with separate relays Number of Communication Processors: 1 If a monitor is removed from slot 2, 8, or 10, no data is returned from that monitor group to the Communication Processors. Monitor Group Figure Example Monitor Assigned to Data Manager Port 1 Monitor Assigned to Data Manager Port 2
