9200-06-02-10-00系統模塊卡件
規格規格
約為+22°C（+72°F），機殼振動速度為25 mm/s（1 in/s），100 Hz（6000 cpm），10 k? 負載，除非另有規定。電靈敏度20 mV/mm/s（500 mV/in/s），正確端接并以校準角度定向時為±5%。校準負載10 kΩ端子“A”至“B”通過引腳“A”和“B”獲得的輸出靈敏度溫度系數0.2%/°C頻率響應-參見第8頁的“理論速度地震探頭頻率響應”4.5至1000 Hz（270至60000 CPM）+典型值為0，-3dB。10至1000 Hz（600至60000 CAM）+典型值為0，-3dB。15至1000 Hz（900至60000 CPM）+典型值為0，-3dB。頻率響應從最小工作頻率（見訂購信息）到1 kHz（60000 cpm）+典型值為0，-3dB。有關詳細校準數據，請聯系Bently Nevada LLC。動態工作范圍2.54 mm（0.100 in）峰間最大位移。速度范圍25 mm/s（1 in/s）（在+22°C下，100 Hz下，10 kΩ負載，外殼振動。線圈電阻1.25 kΩ±5%鎖定線圈電感125 mH，典型振幅線性度±5%，100 Hz（6000CPM）下，0.01至5.0 in/s（0.254至127 mm/s），耐沖擊，沿非敏感軸承受50 g峰值最大加速度。在100 Hz和1.0 in/s（2.54 cm/s）下，橫向靈敏度為敏感軸靈敏度的最大值±10%。當傳感器外殼速度朝向連接器時，輸出信號引腳A的極性相對于引腳B為正。
Seismoprobe速度傳感器
3300或3500監測器之間的導線長度最大為305米（1000英尺）。請參考手冊，了解更長長度的頻率衰減。環境限制操作和儲存溫度：9200:-29°C至+121°C（-20°F至+250°F）。74712:-29°C至+204°C（-20°F至+400°F）。：環境防塵防潮。注意：關于傳感器在輻射環境中的操作，請聯系您的銷售專業人員。相對濕度至95%，不凝結。100%，非浸沒式，與整體電纜一起訂購時。機械外殼和適配器材料陽極氧化鋁A204墊片材料9200：氯丁橡膠74712：硅膠連接器材料頂部和側面安裝選項鍍鎘鋁、氯丁橡膠和鍍銀銅接線板選項帶鍍鎳銅觸點的聚苯硫醚。安裝扭矩?-20、?-20、?-28、5/8-18或M10x1安裝底座選項：5.6 Nm（50 in-lb）9200和74712 Seismoprobe速度傳感器數據表3/14 141626 Rev.L 8-32螺紋螺柱1.41 Nm（12.5 in-lb）典型物理高度102 mm（4 in）（取決于連接器選項）。直徑通常為41 mm（1.6英寸）。重量9200=300克（10.5盎司）。74712=典型的480克（17盎司）。Seismoprobe速度傳感器方向所有Seismorobe速度傳感器都指定了安裝方向，參見“圖表
Specifications
Approximately+22 ° C (+72 ° F), casing vibration speed 25 mm/s (1 in/s), 100 Hz (6000 cpm), 10 k ? load, unless otherwise specified. The electrical sensitivity is 20 mV/mm/s (500 mV/in/s), which is ± 5% when correctly terminated and oriented at the calibration angle. The output sensitivity temperature coefficient 0.2%/° C frequency response obtained by calibrating the load 10 k Ω terminals "A" to "B" through pins "A" and "B" - see "Theoretical speed seismic probe frequency response" 4.5 to 1000 Hz (270 to 60000 CPM) on page 8+typical value is 0, - 3dB. 10 to 1000 Hz (600 to 60000 CAM)+0, - 3dB typical. 15 to 1000 Hz (900 to 60000 CPM)+0, - 3dB typical. Frequency response from minimum operating frequency (see ordering information) to 1 kHz (60000 cpm)+typical value is 0, - 3dB. Contact Bently Nevada LLC for detailed calibration data. Dynamic working range: 2.54 mm (0.100 in) peak to peak maximum displacement. The speed range is 25 mm/s (1 in/s) (at+22 ° C, 100 Hz, 10 k Ω load, and the housing vibrates. The coil resistance is 1.25 k Ω ± 5%, and the coil inductance is 125 mH. The typical amplitude linearity is ± 5%. At 100 Hz (6000 CPM), 0.01 to 5.0 in/s (0.254 to 127 mm/s), it is impact resistant, and it bears 50 g peak maximum acceleration along the non sensitive axis. At 100 Hz and 1.0 in/s (2.54 cm/s), the lateral sensitivity is ± 10% of the maximum sensitivity of the sensitive shaft. When the speed of the sensor housing faces the connector, the polarity of output signal pin A is positive relative to pin B.
Seismoprobe speed sensor
The maximum wire length between 3300 or 3500 monitors is 305 meters (1000 feet). Refer to the manual for longer frequency attenuation. Environmental limitations Operating and storage temperatures: 9200: - 29 ° C to+121 ° C (- 20 ° F to+250 ° F). 74712: - 29 ° C to+204 ° C (- 20 ° F to+400 ° F).: The environment is dust-proof and moisture-proof. Note: Please contact your sales professional about the operation of the sensor in the radiation environment. Relative humidity to 95%, non condensing. 100%, non submerged, when ordered with integral cable. Mechanical housing and adapter material Anodized aluminum A204 Gasket material 9200: Neoprene 74712: Silicone connector material Top and side mounting options Cadmium plated aluminum, Neoprene and silver plated copper terminal block options Polyphenylene sulfide with nickel plated copper contacts. Installation torque ?- 20、 ?- 20、 ?- 28, 5/8-18 or M10x1 mounting base option: 5.6 Nm (50 in lb) 9200 and 74712 Seismoprobe speed sensor data sheet 3/14 141626 Rev. L 8-32 threaded stud 1.41 Nm (12.5 in lb) typical physical height 102 mm (4 in) (depending on connector option). The diameter is typically 41 mm (1.6 inches). Weight 9200=300 grams (10.5 ounces). 74712=typical 480 g (17 oz). Seismoprobe speed sensor direction All Seismoprobe speed sensors have specified installation direction, see "Diagram
