DS200TCQCG1BJF工控模塊備件
在電源線頻率下
在250? 負載輸出溫度漂移0.005%滿量程/°C輸出回讀精度±4%滿量程輸出電流線性度±0.05%滿量程標稱分辨率±0.05%全量程校準精度±0.35%滿量程（25oC），包括線性度直接設定輸出電流范圍0 mA，2.9 mA至21.1 mA最大電阻負載（24 V電源=22 VDC至28 VDC）800歐姆Experion C系列I/O規格，EP03-490-520 22版本1.5霍尼韋爾專有2021 12月參數規范最大輸出兼容電壓（24 V電源=22 VDC到28 VDC）16 V最大開路電壓22 V響應時間（DAC輸入代碼到輸出）在最大10 ms切換時輸出到現場的80 ms間隙（0 mA）內沉降到最終值的1%以內（僅適用于冗余）Experion Series-C I/O規范，EP03-490-520 23版本1.5霍尼韋爾專有2021 12月9。
模擬輸出
具有HART–CC-PAOH51功能模擬輸出（AO）模塊向執行器和記錄/指示設備提供高電平恒定電流。值得注意的功能?廣泛的自診斷?可選冗余?HART可用于狀態和配置?安全狀態（FAILOPT）行為可按通道配置?非易燃輸出FAILOPC系列AO模塊支持按通道的FAILOPD參數。用戶可以將每個通道配置為保持最后一個值或設置為安全值。如果IOM設備電子設備發生故障，輸出將始終歸零，即安全狀態。
At power line frequency
The output temperature drift of 250 Ω· load is 0.005% of the full range/° C, the output readback accuracy is ± 4% of the full range output current, the linearity is ± 0.05% of the full range nominal resolution is ± 0.05% of the full range calibration accuracy is ± 0.35% of the full range (25oC), including the linearity, the direct setting output current range is 0 mA, 2.9 mA to 21.1 mA, the maximum resistance load (24 V power supply=22 VDC to 28 VDC), 800 ohm Experion C series I/O specifications, EP03-490-520 22 version 1.5 Honeywell proprietary 2021 December parameter specification Maximum output compatible voltage (24 V power supply=22 VDC to 28 VDC) 16 V maximum open circuit voltage 22 V response time (DAC input code to output) The 80 ms gap (0 mA) output to the site during maximum 10 ms switching subsides to within 1% of the final value (only applicable to redundancy) Experience Series-C I/O specification, EP03-490-520 23 version 1.5 Honeywell proprietary 2021 December 9.
Analog Output
The analog output (AO) module with HART – CC-PAOH51 function provides high level constant current to the actuator and recording/indicating equipment. Notable functions ? Extensive self diagnosis ? Optional redundancy ? HART can be used for status and configuration ? Safe state (FAILOPT) behavior can be configured by channel ? Non incendive output FAILOPC series AO modules support FAILOPD parameters by channel. You can configure each channel to hold the last value or set it as a safe value. If the electronic device of the IOM device fails, the output will always return to zero, that is, the safe state.
