WOODWARD 9907-166工控模塊機器人備件
警告：
必須重新安裝CF卡鎖緊螺釘，以振動要求滿足危險位置、機械沖擊和振動要求。F C E A B D顯示計算機顯示危險場所的工業計算機29自動化出版物6181X-IN001D-EN-P-2015年7月12日。擰緊固定驅動器托架槽蓋的螺釘（L）。13.按照第24頁的后期配置步驟。在底部CF卡插槽中安裝卡按照這些步驟在底部CF卡插槽中安裝CF卡。1.擰松固定CF卡插槽蓋的螺釘（A）。2.打開CF卡插槽蓋（B）。如有必要，按下鉸鏈側的按鈕，取出插入的卡。3.將新的CF卡插入插槽，直到其牢固就位（C）。4.關閉CF卡插槽蓋（D）。警告：所有計算機型號底部的CF卡插槽都可以熱插拔，但只能位于非危險位置。您可以在計算機運行時從該插槽插入或取出卡。當計算機在危險位置使用時，除非電源已關閉，否則不要在底部CF卡插槽中插入或取出卡。
正確安裝
注意：正確安裝后，在遇到阻力之前，超過80%的CF卡很容易插入插槽。如果您很快遇到阻力，請取出卡，將其旋轉180°，然后重新插入。不要強行將卡插入插槽，否則會損壞連接器引腳。G J H L K I顯示計算機顯示用于危險場所的30臺工業計算機自動化出版物6181X-IN001D-EN-P-2015年7月5.擰緊CF卡槽蓋螺釘（E）。安裝插件卡按照以下步驟安裝插件卡。1.斷開計算機的電源。2.從計算機上卸下后蓋。有關詳細信息，請參閱第25頁的“拆下封面”說明。3.擰下固定槽蓋的一個螺釘。不要丟棄螺釘。4.拆下槽蓋并將其存放起來，以便稍后重新組裝。5.握住擴充卡的邊緣，將其從保護包裝中取出。6.將擴充卡連接到兼容的轉接板插槽。驗證卡是否正確安裝在插槽中。7.用插槽蓋上的螺釘固定擴充卡。
Warning:
The CF card locking screws must be reinstalled to meet the vibration requirements for hazardous locations, mechanical shock and vibration. F C E A B D Display Computer Display Industrial Computer in Hazardous Locations 29 Automation Publication 6181X-IN001D-EN-P-2015, July 12. Tighten the screws (L) that secure the drive bay slot cover. 13. Follow the post configuration steps on page 24. Installing a card in the bottom CF card slot Follow these steps to install a CF card in the bottom CF card slot. 1. Loosen the screw (A) that secures the CF card slot cover. 2. Open the CF card slot cover (B). If necessary, press the button on the hinge side to remove the inserted card. 3. Insert the new CF card into the slot until it is firmly seated (C). 4. Close the CF card slot cover (D). Warning: The CF card slot on the bottom of all computer models can be hot swapped, but can only be located in a non hazardous location. You can insert or remove a card from this slot while the computer is running. When the computer is used in a dangerous location, do not insert or remove a card from the bottom CF card slot unless the power is turned off.
Correct installation
Note: After correct installation, more than 80% of CF cards can easily be inserted into the slot before encountering resistance. If you soon encounter resistance, remove the card, rotate it 180 °, and then reinsert it. Do not force the card into the slot, or the connector pins will be damaged. G J H L K I display computer shows 30 industrial computers used in hazardous areas Automation publication 6181X-IN001D-EN-P-2015 July 5. Tighten CF card slot cover screws (E). To install the plug-in card, follow the steps below to install the plug-in card. 1. Disconnect the power of the computer. 2. Remove the back cover from the computer. For details, refer to the instructions "Removing the Cover" on page 25. 3. Unscrew one screw fixing the slot cover. Do not discard the screws. 4. Remove the tank cover and store it for later reassembly. 5. Hold the expansion card by its edges and remove it from the protective package. 6. Connect the expansion card to a compatible docking station slot. Verify that the card is properly installed in the slot. 7. Secure the expansion card with the screws on the slot cover.
