VMIVME-7671-421000燃機工控模塊
時負載電流
限制在約 當–差分降低到 以下時負載電壓限制在約 注意：在施加輸入電壓后切換啟用時當引腳第一次變高時折返電流限制電路正常工作在引腳被取高的第二次和隨后的時間折返電流限制電路不起作用根據輸入和輸出電容值輸入涌入電流可能高于預期值這可能導致輸入電壓下降如果引腳連接到引腳則當從低于 開始時當應用時折返電流限制電路正常工作設備功能模式啟用引腳電壓必須高于閾值以確保設備在所有操作條件下都完全啟用最低工作輸入電壓和設備不包括任何專用電路在至少為 之前和內部電路不能完全工作在之前輸出電壓不能調節或以較高者為準
產品文件夾鏈接：
提交文檔反饋版權所有?–德克薩斯儀器公司應用和實施注釋以下應用部分中的信息不屬于組件規范的一部分不保證其準確性或完整性的客戶負責確定組件是否適合其用途客戶應驗證和測試其設計實現以確認系統功能應用信息反向電壓當輸出引腳的電壓高于輸入引腳的電壓時存在反向電壓條件通常當突然變低并且繼續保持足夠的電荷使得輸入到輸出電壓變?yōu)榉聪驎r(shí)就會發生這種情況一種不太常見的情況是當交流電壓源連接到輸出端時在反向電壓條件下電流有兩種可能從輸出引腳流回輸入當足夠高以保持控制電路活動且引腳（僅限）高于閾值時控制電路嘗試調節輸出電壓如果輸入電壓小于編程輸出電壓則控制電路將元件的柵極驅動至完全開啟狀態在這種情況下反向電流從輸出引腳流向輸入引腳僅受元件
Hourly load current
The load voltage is limited to about when the difference drops to the following. Note: When the input voltage is applied, the switch is enabled. When the pin becomes high for the first time, the turn back current limiting circuit works normally. The turn back current limiting circuit does not work at the second and subsequent time when the pin is high. According to the input and output capacitance values, the input inrush current may be higher than the expected value. This may cause the input voltage to drop. If the pin is connected to the pin From below at the beginning, when it is applied, the turnback current limiting circuit works normally. The enabled pin voltage of the device function mode must be higher than the threshold value to ensure that the device is fully enabled under all operating conditions. The minimum operating input voltage and the device do not include any special circuit at least before and the internal circuit cannot work completely before. The output voltage cannot be adjusted or whichever is higher
Product folder link:
Submit document feedback Copyright ?– Texas Instruments Application and Implementation Note The information in the following application sections is not part of the component specification. It is not guaranteed that its accuracy or completeness. The customer is responsible for determining whether the component is suitable for its purpose. The customer should verify and test its design implementation to confirm the system function. Application information. Reverse voltage. When the voltage of the output pin is higher than the voltage of the input pin, there is a reverse voltage condition. Usually, when the voltage suddenly decreases and continues to be sufficient This happens when the charge causes the input to output voltage to become reverse. It is an uncommon case that when the AC voltage source is connected to the output terminal, there are two possibilities for the current to flow back from the output pin to the input when it is high enough to keep the control circuit active and the pin (only) If the input voltage is less than the programmed output voltage, the control circuit drives the gate of the element to the fully open state. In this case, the reverse current flows from the output pin to the input pin only by the element
