MIVME-7666-111000350-017666-111000 C工控模塊系統備件
輸出到輸入電壓
差的限制以這種方式放電高達μ的輸出電容器不會損壞器件因為電流會迅速衰減但是應避免連續反向電流當引腳低時可防止這種情況內部 元件具有固有的寄生二極管在正常操作期間輸入電壓高于輸出電壓并且寄生二極管被反向偏置然而當?shù)陀诳刂齐娐酚行У闹祷蛘咭_低（僅限）并且輸出電壓高于輸入電壓 （典型值）時寄生二極管變?yōu)檎蚱秒娏鲝妮敵鲆_通過二極管流向輸入引腳寄生二極管中的電流應限制在一個連續的峰值如果在雙電源系統中使用其中調節器輸出負載返回到負電源則輸出引腳必須二極管鉗位接地以限制負電壓過渡此保護鉗建議使用肖特基二極管
產品文件夾鏈接：
版權所有?–德克薩斯儀器公司提交文件反饋典型應用穩定性所需的最小值僅限軟件包設備圖典型應用穩定性所需的最小值僅限軟件包設備圖典型應用設計要求對于典型的穩壓器應用使用表中列出的參數表設計參數設計參數示例值輸入電壓范圍至 輸出電壓 輸出電流 輸出電流范圍μ輸入/輸出計算器范圍提交文件反饋版權所有?–德州儀器公司詳細設計程序功率分配和設備操作任何包裝的允許功率分配是設備對電源熱量的耐受性的量度設備的連接點最終的散熱器周圍環境因此功率分布取決于環境溫度和管芯結與環境空氣之間的各種界面上的熱阻任何包裝
Output to input voltage
Poor limits discharge in this way up to μ The output capacitor will not damage the device because the current will decay rapidly, but continuous reverse current should be avoided. This can be prevented when the pin is low. The internal components have inherent parasitic diodes. During normal operation, the input voltage is higher than the output voltage and the parasitic diodes are reverse biased. However, when it is lower than the effective value of the control circuit or the pin is low (only) and the output voltage is higher than the input voltage (typical value) When the parasitic diode becomes a positive bias current, the current flowing from the output pin through the diode to the input pin in the parasitic diode should be limited to a continuous peak. If the output load of the regulator returns to the negative power supply in a dual power supply system, the output pin must be grounded by the diode clamp to limit the negative voltage transition. This protective clamp is recommended to use Schottky diodes
Product folder link:
copyright ?– Documents submitted by Texas Instruments Co., Ltd. The minimum value required for stability of typical applications is limited to software package equipment diagram The minimum value required for stability of typical applications is limited to software package equipment diagram Typical application design requirements For typical voltage regulator applications Use the parameter table listed in the table Design parameter Example value Input voltage range to output voltage Output current range μ Input/output calculator range Submit document feedback copyright ?– Texas Instruments detailed design program Power distribution and equipment operation The allowable power distribution of any package is a measure of the resistance of the equipment to the heat of the power supply The connection point of the equipment The final surrounding environment of the radiator Therefore, the power distribution depends on the ambient temperature and the thermal resistance of various interfaces between the pipe core junction and the ambient air Any package
