VMIVME-7664備件庫存
允許功耗
是衡量設備從電源設備連接點到最終散熱器和周圍環境散熱的能力因此功率分布取決于環境溫度和管芯結與環境空氣之間的各種界面上的熱阻給定包裝中設備的最大允許功率分配可使用等式計算設備中分配的實際功率可由等式表示：器件兩端的電壓降以及器件的連續電流適應性這兩個方程應用于確定應用中設備的最佳操作條件在存在較低功耗和/或優異封裝熱阻的應用中最高環境溫度可能會增加在存在高功率耗散和/或不良封裝熱阻的應用中可能必須降低最高環境溫度取決于最大工作結溫度（=°）應用中器件封裝的最大允許功率分布以及應用中器件
封裝的結對環境熱阻必須減小值
這可以通過在–期限內減少來實現只要滿足最小或者通過減少期限或者通過兩者的某種組合來實現外部計算器與大多數調節器一樣和需要外部計算器來保持調節器的穩定性和專門為需要最小板尺寸和最小組件的便攜式應用而設計必須正確選擇這些主管才能獲得良好的績效輸入計算器穩定性需要輸入計算器建議在或 引腳和引腳之間連接一個μ的電容器（該電容值可以無限制地增加）該控制器必須位于距引腳不超過 的位置并返回到干凈的模擬接地輸入端可使用任何優質陶瓷鉭或薄膜電容器重要：為了確保穩定運行必須采用良好的設計實踐以最小化接地阻抗并保持輸入電感
Allowable power consumption
It measures the ability of equipment to dissipate heat from the power supply equipment connection point to the final radiator and the surrounding environment. Therefore, the power distribution depends on the ambient temperature and the thermal resistance on various interfaces between the tube core junction and the ambient air. The maximum allowable power distribution of the equipment in a given package can be calculated using equations. The actual power distributed in the equipment can be expressed by equations: the voltage drop at both ends of the device and the continuous current adaptability of the device. These two equations are used to determine the The best operating conditions of the equipment in use. In applications with low power consumption and/or excellent package thermal resistance, the maximum ambient temperature may increase. In applications with high power dissipation and/or poor package thermal resistance, the maximum ambient temperature may have to be reduced. The maximum ambient temperature depends on the maximum allowable power distribution of the device package in the application (=°) and the device in the application
The environmental thermal resistance of the package must be reduced
This can be achieved by reducing within the – period as long as it meets the minimum or by reducing the period or by some combination of the two. External calculators are the same as most regulators and need external calculators to maintain the stability of regulators and are specially designed for portable applications that require minimum board size and minimum components. These supervisors must be selected correctly to obtain good performance. Input stability of calculators requires input calculations It is recommended to connect a μ The controller must be located no more than the pin and returned to a clean analog grounding input. Any high-quality ceramic tantalum or film capacitor can be used. Important: To ensure stable operation, good design practices must be used to minimize the grounding impedance and maintain the input inductance
