VMIVME-4514A PLC備件
模塊不提供非再生單元
裝置可容納頂部入口和底部出口。底部入口需要額外的部分。 在此處添加選項代碼。用破折號分隔選項代碼。頂部出口需要單獨的附加部分。需要單獨訂購單獨安裝的至現場隔離變壓器。請參閱第節電源模塊同步丟失故障避免警告第位系統通過交流線路電壓的臨時丟失繼續運行。如果交流線路電壓缺失超過秒系統將立即進入空閑狀態并在寄存器中設置位交流線路同步故障。電流限值警告第位電流值已超過作為最大電流限值配置參數輸入的值。識別測試錯誤警告第位電樞識別磁場識別測試失敗。
設置此位
當分解器平衡校準測試失敗產生意外結果時也會設置此位?，F(xiàn)場電源模塊過電流警告位現場電源模塊的現場電流反饋值在秒內大于熱場電流參數的倍。這種情況可能會在現場測試期間現場開啟時導致錯誤。這些錯誤可能是由于和交流輸入線與現場電源模塊的布線不當造成的。風扇損失警告第位位于電源模塊中的氣流開關檢測到風扇損失。通常應用程序任務應在合理短的時間內停止驅動器以防止損壞設備。檢查風扇是否運轉空氣通道是否清潔。部件更換電源模塊采用模塊化設計可快速方便地更換部件。為電樞電力結構部件提供備件包。
The module does not provide a non regenerative unit
The unit can accommodate the top inlet and bottom outlet. An additional section is required for the bottom entrance. Add an option code here. Separate option codes with dashes. A separate additional section is required for the top outlet. Separately installed isolation transformers to the site need to be ordered separately. Refer to Section Power Module Synchronization Loss Failure Avoidance Warning The system continues to operate through the temporary loss of AC line voltage. If the AC line voltage is lost for more than seconds, the system will immediately enter the idle state and set the bit AC line synchronization fault in the register. Current limit warning The bit current value has exceeded the value entered as the maximum current limit configuration parameter. Identification test error warning Armature position identification magnetic field identification test failed.
Set this bit
This bit is also set when the resolver balance calibration test fails and produces unexpected results. The field current feedback value of the field power module at the overcurrent warning position of the field power module is greater than times of the thermal field current parameter within seconds. This condition may cause errors when the field is opened during field testing. These errors may be caused by improper wiring between the and AC input lines and the field power module. Fan loss warning The air flow switch located in the power module detects a fan loss. Generally, application tasks should stop the drive in a reasonably short time to prevent damage to the device. Check whether the fan is running and whether the air passage is clean. The modular design of the power module for component replacement can quickly and conveniently replace components. Provide spare parts kits for armature power structure components.
