VMIVME332-004512-300J自動化模塊
電壓常數伏 端子電阻歐姆
要獲得以秒為單位的振動速度請使用以下公式： 其中：＝以秒表示的振動速度＝峰值至峰值位移單位：電機轉速 系列伺服電機出版物年月圖 和 旋轉變壓器和高分辨率電機的電機速度扭矩曲線重要：所示曲線和性能數據適用于放大器額定值大于等于電機持續失速電流的電機和組合。在環境中在 的線路電壓下測試電機。外殼溫度約為電機繞組比環境溫度升高。當電機安裝在 × 鋼安裝支架上時確定扭矩額定值。電機包含兩個串聯的熱開關在超溫條件下打開。溫度設置為%。觸點的額定值為 時為 時為。下面顯示的所有值的公差為%。類別參數環境溫度。機組 時的一般連續失速扭矩額定輸出 峰值失速扭矩時的
安培峰值失速電流時的安培
時的機械時間常數毫秒 下的電氣時間常數毫秒 額定轉速 最高環境溫度無降額攝氏度 絕緣等級熱時間恒定分鐘 時的繞組扭矩恒定 伏特 時的電壓恒定 時的終端電阻歐姆電機重量平衡 使用以下公式： 其中：振動速度單位：秒峰間位移單位：毫米電機轉速 轉速扭矩電機峰值峰值續。 額定運行間歇運行額定轉速 轉速扭矩電機峰值峰值續續峰值 系列交流伺服電機出版物年月圖 和旋轉變壓器和高分辨率電機的電機速度扭矩曲線重要：所示曲線和性能數據適用于放大器額定值大于等于電機持續失速電流的電機和組合。在環境中在 的線路電壓下測試電機。外殼溫度約為電機繞組比環境溫度升高。當電機安裝在 × 鋼安裝支架上時確定扭矩額定值。電機包含兩個串聯的熱開關在超溫條件下打開。溫度設置為%。
Voltage Constant Volt Terminal Resistance Ohms
To obtain the vibration speed in seconds, please use the following formula: where:=vibration speed in seconds=peak to peak displacement unit: motor speed series servo motor publications monthly chart and motor speed torque curve of resolver and high resolution motor Important: The curves and performance data shown are applicable to motors and combinations with amplifier ratings equal to or greater than the motor continuous stall current. Test the motor in the environment at line voltage of. The enclosure temperature is about the motor winding temperature is higher than the ambient temperature. When the motor is installed on the × Determine the torque rating when mounting on the steel bracket. The motor contains two thermal switches in series that open under overtemperature conditions. The temperature is set to%. When the rating of the contact is, it is. The tolerance for all values shown below is%. Category parameter ambient temperature. General continuous stall torque at unit time Rated output peak stall torque
Ampere at peak stall current
When the mechanical time constant is millisecond, the electrical time constant is millisecond, the rated speed, the maximum ambient temperature, no derating, degree Celsius, the insulation grade, the winding torque, constant minute, the winding torque, constant volt, the voltage, constant terminal resistance, ohm motor weight balance, use the following formula: where: vibration speed unit: second peak displacement unit: millimeter motor speed, speed, torque, motor peak peak to peak continued. Rated Operation Intermittent Operation Rated Speed Speed Torque Motor Peak Peak Value Continued Peak Value Series AC Servo Motor Publications Monthly Chart and Motor Speed Torque Curves for Resolvers and High Resolution Motors Important: The curves and performance data shown are applicable to motors and combinations with amplifier ratings equal to or greater than the motor's continuous stall current. Test the motor in the environment at line voltage of. The enclosure temperature is about the motor winding temperature is higher than the ambient temperature. When the motor is installed on the × Determine the torque rating when mounting on the steel bracket. The motor contains two thermal switches in series that open under overtemperature conditions. The temperature is set to%.
