VMIVME-250B工控備件模塊
產品數據
該點的定義是，電機溫度為25°C，控制器溫度為60°C。產品數據1326AB交流伺服電機10額定運行區域——速度-轉矩曲線的邊界，其中電機和控制器組合可在伺服基礎上運行，而不超過任何一個的RMS額定值。公式詳情見第31頁。Tpa2 x t1+Tss2 x t2+Tpd2 x t3+Tr2 x t4 t1+t2+t3+t4 RMS扭矩=間歇運行區域–速度-扭矩曲線的邊界，在不超過占空比RMS連續扭矩限制的情況下，電機和控制器組合可在加速-減速模式下運行，而不超過兩者的峰值額定值。連續電流–在額定溫度和40°C環境下，帶繞組的電機的額定電流。
控制器
在60°C的額定環境下運行。峰值電流–在不損壞電機的情況下施加到電機的電流量。機械時間常數–施加階躍電壓時，電機達到最終速度63%所需的時間。電氣時間常數–電機達到額定電流63%所需的時間。最高環境溫度——電機可在額定負載下運行而不超過其絕緣型溫升極限的最高環境溫度。絕緣等級——電機絕緣材料工作溫度極限的指定。熱時間常數——電機繞組達到連續溫升63%的時間，損耗恒定。扭矩恒定–在規定的電機溫度下，一安培電機電流產生的扭矩量。電壓常數–當轉子在磁場中機械移動時，在指定速度下產生的電壓值。
Product Data
This point is defined as a motor temperature of 25 ° C and a controller temperature of 60 ° C. Product data 1326AB AC servo motor 10 rated operation area - the boundary of speed torque curve, where the combination of motor and controller can operate on the basis of servo without exceeding the RMS rating of any one. See page 31 for formula details. Tpa2 x t1+Tss2 x t2+Tpd2 x t3+Tr2 x t4 t1+t2+t3+t4 RMS torque=Intermittent operation area – boundary of speed torque curve. Under the condition that the continuous torque limit of duty cycle RMS is not exceeded, the combination of motor and controller can operate in acceleration deceleration mode without exceeding the peak value rating of both. Continuous Current – The rated current of a motor with windings at rated temperature and 40 ° C.
controller
Operate in a rated environment of 60 ° C. Peak Current – The amount of current applied to the motor without damaging it. Mechanical Time Constant – The time it takes for the motor to reach 63% of its final speed when a step voltage is applied. Electrical time constant – the time required for the motor to reach 63% of the rated current. Maximum ambient temperature - the maximum ambient temperature at which a motor can operate under rated load without exceeding its insulation type temperature rise limit. Insulation class - designation of operating temperature limits of motor insulation materials. Thermal time constant - the time when the motor winding reaches 63% of continuous temperature rise, and the loss is constant. Constant torque – The amount of torque produced by one ampere of motor current at the specified motor temperature. Voltage Constant – The value of the voltage produced at a specified speed when the rotor is mechanically moving in a magnetic field.
