TRICONEX 9785-610工控模塊
套件說明?主控制板更換固件版本內容本文檔介紹了如何卸下和更換再生直流母線電源單元中的主控制板。此套件包含的內容使用下表，驗證您是已收到套件中的適當項目：其他需要的項目在開始之前，請確保您還具備以下各項：您需要的工具：–測量電壓–拆卸松開，和緊固螺釘包括端子螺釘–扭轉螺釘至至文檔：–您的驅動系統示意–出版物，再生直流母線供電單元–用戶手冊本部分：您應該收到此數量：主控板腕帶出版物年月?主控制板更換固件版安全注意事項在維修或驅動系統配置時，
特別說明重要提示：
您需要重新使用從設備上拆下的零件。按照拆下的順序?qū)⒘慵旁诟蓛舻谋砻嫔?。重要提示：新的主控制板可能不包括與現有板相同的參數設置。如有必要，請?jiān)诟鼡Q主控制板之前記錄參數設置！注意：只有熟悉驅動系統系統中使用的產品和相關機械的人員才能計劃或?qū)嵤┫到y(tǒng)的安裝啟動和未來維護。不遵守可能導致人身傷害和或設備損壞。注意：根據第二部分的要求，驗證所有交流和直流電源是斷電上鎖或掛牌。
Kit Description ? Main control board replacement firmware version content This document describes how to remove and replace the main control board in the regenerative DC bus power supply unit. Contents of this kit Use the following table to verify that you have received the appropriate items in the kit: Other required items Before starting, please ensure that you also have the following items: Tools you need: – Measuring voltage – Removing and loosening, and fastening screws including terminal screws – Twisting screws to documents: – Your drive system schematic – Publications, Regenerative DC bus power supply unit – user manual This part: You should receive this quantity: master control board wrist strap publication Month Year ? Safety precautions for replacing firmware version of main control board,
Special notes Important notes:
You need to reuse the parts removed from the equipment. Place the parts on a clean surface in the order they were removed. Important: The new main control board may not include the same parameter settings as the existing board. If necessary, record the parameter settings before replacing the main control board! Note: Only personnel familiar with the products and related machinery used in the drive system can plan or implement the installation, startup and future maintenance of the system. Failure to comply may result in personal injury and or equipment damage. Note: According to the requirements of Part II, verify that all AC and DC power supplies are locked out or tagged out.
