UFC721BE101備件模塊
?雙擊監視器設置窗格中的間隔（ms）字段，或在監視器菜單或監視器設置的上下文菜單中選擇間隔命令?；颉伴g隔（ms）”對話框，其編輯字段中顯示當前值。編輯或輸入新的（整數）值，然后單擊“確定”。如果要取消操作，請單擊“取消”按鈕。新值顯示在監視器設置窗格中。間隔有限制：?值必須是大于零的整數。?該值不能大于當前x軸長度（以毫秒為單位）。?如果監控模式正常，該值必須至少為10。?與x軸長度相關的值不得太小，即x軸長度（毫秒）除以該值不得超過32700。?x軸長度（以毫秒為單位）必須是該值的倍數。例如，如果x軸長度為1秒，則間隔3ms是不可接受的。然后必須固定x軸長度或使用其他間隔。趨勢驅動窗口2 6-23如果該值無效，單擊確定按鈕時將顯示錯誤消息。您必須確認錯誤消息并編輯無效值或取消操作。如果監控模式正常，并且您輸入的值小于10，則單擊“確定”按鈕時會顯示錯誤消息。您必須確認錯誤消息，將值更改為至少10或取消操作。趨勢6-24 DriveWindow 2如果您輸入的值因當前x軸長度和/或歷史緩沖區大小而不可接受，您可以選擇固定x軸長度或歷史緩沖大小。如果單擊“是”，則接受間隔，但x軸長度和/或歷史緩沖區大小也會更改。另請參閱：通用趨勢設置恢復默認設置設置監視器監視器和數據記錄器監視器設置監視器菜單監視器設置的上下文菜單3.3設置歷史緩沖區大小監視器將數據收集到歷史緩沖區中。歷史緩沖區可以收集比屏幕上顯示的數據更多的數據。當監視器暫?；蛲Ｖ箷r，可以在監視器顯示窗格中滾動歷史緩沖區中的數據。當歷史緩沖區填充時，將忽略最舊的數據。只有在清除監視器時，才能更改歷史緩沖區大小。請注意，歷史緩沖區大小必須是間隔的倍數。趨勢驅動窗口2 6-25要更改歷史緩沖區大?。?如果尚未選擇，請選擇趨勢設置窗格中的監視器選項卡。?雙擊監視器設置窗格中的歷史緩沖區字段，或在監視器菜單或監視器設置的上下文菜單中選擇歷史緩沖區命令?；蝻@示“歷史緩沖區”對話框，其編輯字段中顯示當前值。編輯或輸入新的（實際）值，然后單擊“確定”。如果要取消操作，請單擊“取消”按鈕。
? Either double-click the Interval (ms) field in the monitor settings pane, or select the Interval command in the Monitor menu or in the context menu of Monitor Settings. or An Interval (ms) dialog box is presented with the present value shown in its edit field. Edit or enter a new (integer) value and click OK. If you want to cancel the operation, click the Cancel button. The new value is shown in the monitor settings pane. There are restrictions about the interval: ? The value must be an integer greater than zero. ? The value cannot be bigger than the current x-axis length in milliseconds. ? If monitoring mode is normal, the value must be at least 10. ? The value must not be too small related to x-axis length, i.e., x-axis length in milliseconds divided by the value must not exceed 32700. ? X-axis length in milliseconds must be multiple of the value. For example, if x-axis length is 1 second, interval 3 ms is not acceptable. You must then either fix the x-axis length or use another interval. Trends DriveWindow 2 6-23 If the value is invalid, an error message is displayed, when you click the OK button. You have to acknowledge the error message and edit the invalid value or cancel the operation. If the monitoring mode is normal and you have entered a value less than 10, an error message is displayed, when you click the OK button. You have to acknowledge the error message change the value to at least 10 or cancel the operation. Trends 6-24 DriveWindow 2 If you have entered value that is not acceptable because of the current x-axis length and/or history buffer size, you have the option to fix the x-axis length and/or the history buffer size. If you click Yes, your interval is accepted, but the x-axis length and/or history buffer size is changed, too. See Also: Common Trend Settings Restoring Default Settings Setting Monitor Monitor and Dataloggers Monitor Settings Monitor Menu Context Menu of Monitor Settings 3.3 Setting History Buffer Size The monitor collects data into a history buffer. History buffer makes it possible to have more data collected than fits on the screen. The data in the history buffer can be scrolled in the monitor display pane when the monitor is paused or stopped. When the history buffer fills, the oldest data is disregarded. You can change the history buffer size only when the monitor is cleared. Note that the history buffer size must be multiple of the interval. Trends DriveWindow 2 6-25 To change the history buffer size: ? If not yet selected, select the Monitor tab in the trend settings pane. ? Either double-click the History Buffer (s) field in the monitor settings pane, or select the History Buffer command in the Monitor menu or in the context menu of Monitor Settings. or A History Buffer (s) dialog box is presented with the present value shown in its edit field. Edit or enter a new (real) value and click OK. If you want to cancel the operation, click the Cancel button.
