MVME3604-5131B工控備件模塊
這意味著僅使用SAP/http以太網通信。?禁用端口是一個逗號分隔的COM端口號或不用于SAP通信的編號范圍列表。范圍-n表示0-n，n-表示n-4294967295。OPC服務器7-68 DriveWindow 2搜索設備組該組定義了在連接時是否使用廣播方法搜索SAP/http設備。通常情況下，您不會同時使用這兩種方法。該組包含：?近表示使用本地以太網段UDP廣播（IP=255.255.255.255，RFC 919）。?Intranet表示使用PC子網UDP廣播（IP=IP或非子網掩碼，RFC 922）。請注意，如果PC屬于多個子網，則會廣播所有子網。設備組該組定義SAP/http設備的IP地址（固定IP）。指定的頻道號不能重疊。具有重疊信道號的設備規范在連接時被忽略。OPC服務器DriveWindow 2 7-69注意，所有DriveOPC設備（如果有的話）的信道號都在本地DriveDA信道的最后一個信道號之后移動。該組包含：?IP地址定義IP地址（固定IP）。?“狀態”組中的“否檢查”指定在啟動時不查詢設備的狀態。盡管這可能會加快啟動速度，但大多數通信屬性不可用。?“狀態”組中的“無論如何使用”指定在啟動時查詢設備的狀態，但如果設備沒有響應，則無論如何使用。如果設備不響應狀態查詢，則大多數通信屬性不可用。?頻道號可以為固定IP指定固定的頻道號。負值（-1）表示自動編號（Auto）。協議組該組包含NETA-21特定設置。請注意，如果兩個NETA-21面板總線都在使用，則設備在固定IP列表中顯示兩次，并附加/1和/2。但是，如果Find用于添加IP地址，則只顯示一次，但沒有附加總線號。沒有附加總線號的NETA-21實際上意味著兩個通道，即兩條總線都在使用。還要注意，如果兩個NETA-21面板總線都在使用，則不能為設備指定固定的通道號。如果要做到這一點，應兩次指定相同的設備IP，每個面板總線一個。該組包含：?NETA指定SAP/http設備是否為NETA-21。?NETA通道指定使用NETA-21的哪個面板總線。這兩種方法都可以使用。另請參閱：使用DriveDA DriveWindow 2配置SAP/http連接到OPC服務器8-1第8章-系統軟件內容系統軟件8-2 DriveWindow 2另請參閱系統軟件子菜單1.定義?系統軟件?備份包?加載包1.1什么是系統軟件系統軟件由保存在AMC板閃存prom中的所有持久“文件”組成，排除引導程序。通常，系統軟件文件可分為：?操作系統和電機控制器文件?面板處理文件
It means that only SAP/http Ethernet communication is used. ? Disable Ports is a comma separated list of COM port numbers or number ranges which are not used for SAP communication. A range -n means 0-n and n- means n-4294967295. OPC Server 7-68 DriveWindow 2 Search Devices group The group defines, whether the broadcast methods are used to search SAP/http devices at connection time or not. Typically you never use both of them. The group contains: ? Near means that local Ethernet segment UDP broadcast (IP=255.255.255.255, RFC 919) is used. ? Intranet means that the PC subnet UDP broadcast (IP=IP or not subnet mask, RFC 922) is used. Note that if the PC belongs to several subnets, all of them are broadcasted. Device group The group defines the IP address (Fixed IP) of a SAP/http device. Channel Numbers specified must not overlap. A device specification having an overlapping Channel Number is disregarded at connection time. OPC Server DriveWindow 2 7-69 Note that the channel numbers of all DriveOPC devices (if any) are shifted after the last channel number of the native DriveDA channels. The group contains: ? IP Address defines the IP address (Fixed IP). ? No Check in the Presence group specifies that the presence of the device is not queried at start-up. Although it may speed up the start-up, most of the Communication Properties is not available. ? Use Anyway in the Presence group specifies that the presence of the device is queried at start-up but, if it does not respond, it is used anyway. If the device does not respond to presence queries, most of the Communication Properties is not available. ? Channel Number can specify a fixed channel number for a Fixed IP. Negative value (-1) means automatic numbering (Auto). Protocol group The group contains NETA-21 specific settings. Note that if both NETA-21 panel buses are in use, the device is either shown twice in Fixed IPs list with /1 and /2 appended. However, if Find is used for adding IP addresses, it is shown just once but without an appended bus number. A NETA-21 without an appended bus number means actually two channels, .i.e., both buses are in use. Note also that if both NETA-21 panel buses are in use, you cannot specify a fixed Channel Number for the device. If you want to do that, you should specify the same device IP twice, one for each of the panel buses. The group contains: ? NETA specifies, whether the SAP/http device is NETA-21 or not. ? NETA Channels specifies which of the panel buses of the NETA-21 is used. Also both of them can be used. See Also: Configuring SAP/http Connecting to OPC Server Using DriveDA DriveWindow 2 8-1 Chapter 8 - System Software Contents System Software 8-2 DriveWindow 2 See Also: System Software Submenu 1. Definitions ? System Software ? Backup Package ? Loading Package 1.1 What is System Software System Software consists of all the persistent "files" that are saved in the flash prom of the AMC board, the boot program excluded. Typically System Software files can be divided into: ? Operating System and Motor Controller files ? Panel Handling file
