MVME2434-3工控備件機器人模塊
建議的電源線尺寸3剝線長度7 mm（0.275 in。)4固定直流電源線的扭矩范圍0.22…0.25 N?m（0.16…0.18 ft?lb）0.5…0.6 N?m（0.37…0.44 ft?lb安裝說明圖2-直流連接器組裝順序安裝更換安裝夾要更換VersaView 6300P面板PC和6300M顯示器上的安裝夾，請執行以下步驟。1.斷開計算機或顯示器的電源。2.將替換安裝夾滑入電腦或顯示器側面的孔中，如右圖所示。對于不同的孔位置，請參見第4.3頁圖3。按照第4.4頁圖3中的擰緊順序手動擰緊安裝夾。使用提供的1.5 mm六角扳手，按照第4.5頁圖3的擰緊順序擰緊安裝夾，按照第4.6頁圖3中的擰緊順序，將安裝卡箍擰緊至0.2 N?m（1.8 lb?in）的扭矩。重復此過程至少三次，直到卡箍正確擰緊至0.2 N.m（1.8磅?in）。確認墊片均勻地壓在面板上。重要事項圖2中所示的直流連接器組件僅用于說明目的。直流連接器組件的尺寸、形狀和顏色可能與圖2所示有所不同。
注意：將安裝夾擰緊至規定扭矩，以提供適當?shù)拿芊猓⒂兄诜乐巩a(chǎn)品損壞。羅克韋爾自動化公司對因安裝不當而對外殼內的計算機或其他設備造成的水或化學損壞不承擔任何責任。A B C D E F出版物6300V-IN003A-EN-P-2021 1月|取代出版物XXXX-X.X.X-年月版權所 。不屬于Rockwel Automation的商標是其各自公司的財產。您的意見有助于我們更好地滿足您的文檔需求。如果您對如何改進我們的內容有任何建議，請?jiān)趓ok.auto/docfeedback填寫表格。有關技術支持，請?jiān)L問rok.auto/support*PN-618253*PN-618253廢棄電氣和電子設備（WEEE）羅克韋爾自動化公司在其網站rok.auto/pec上維護當前產品環境合規信息。在使用壽命結束時，該設備應與未分類的城市垃圾分開收集。圖3-安裝 .的緊固和扭矩順序。，和17英寸。顯示尺 和19英寸。顯示尺寸I/O端口18.5英寸。顯示尺寸10 ACI委員會440 ACI 440.2R-17報告的用于加固混凝土結構的外部粘結FRP系統的設計和施工指南2017年5月首次印刷ISBN:978-1-945487-59-0用于加固混凝土的外部粘結玻璃鋼系統的設計與施工指南美國混凝土學會版權所有，密歇根州法明頓山。保留所有權利。未經ACI書面同意，不得在任何印刷、機械、電子、電影或其他分發和存儲介質中復制或復制本材料的全部或部分內容。負責ACI委員會報告和標準的技術委員會努力避免這些文件中的歧義、遺漏和錯誤。盡管做出了這些努力，ACI文件的用戶偶爾會發現信息或要求可能需要多個解釋?zhuān)蛘呖赡懿煌暾虿徽_。
Recommended power cord size 3 Stripping length 7 mm (0.275 in.) 4 Fixed DC power cord torque range 0.22... 0.25 N ? m (0.16... 0.18 ft ? lb) 0.5... 0.6 N ? m (0.37... 0.44 ft ? lb installation instructions Figure 2 - DC connector assembly sequence Installation of replacement mounting clips To replace the mounting clips on the VersaView 6300P panel PC and 6300M monitor, perform the following steps. 1. Disconnect the power from the computer or monitor. 2. Slide the replacement mounting clips into the holes on the side of the computer or monitor, as shown in the right figure. For different hole locations, see Figure 3 on page 4.3. Manually tighten them according to the tightening sequence in Figure 3 on page 4.4 Tighten the mounting clip. Using the supplied 1.5 mm hex wrench, tighten the mounting clamp according to the tightening sequence shown in Figure 3 on page 4.5, and tighten the mounting clamp to a torque of 0.2 N ? m (1.8 lb ? in) according to the tightening sequence shown in Figure 3 on page 4.6. Repeat this process at least three times until the clamp is properly tightened to 0.2 N.m (1.8 lb ? in). Confirm that the gasket is pressed evenly on the panel. IMPORTANT The DC connector assembly shown in Figure 2 is for illustrative purposes only. The size, shape, and color of the DC connector assembly may differ from those shown in Figure 2.
NOTE: Tighten the mounting clips to the specified torque to provide a proper seal and help prevent product damage. Rockwell Automation assumes no responsibility for water or chemical damage to computers or other equipment inside enclosures due to improper installation. A B C D E F Publication 6300V-IN003A-EN-P-2021 January | Supersedes publication XXXX-X.X.X-Copyright Office. Trademarks that are not part of Rockwell Automation are the property of their respective companies. Your comments will help us better meet your documentation needs. If you have any suggestions on how to improve our content, please fill in the form at rok.auto/docfeedback. For technical support, please visit rok Auto/support * PN-618253 * PN-618253 Waste Electrical and Electronic Equipment (WEEE) The current product environment compliance information is maintained on auto/pec. At the end of the service life, the equipment shall be collected separately from the unclassified urban garbage. Figure 3 - Tightening and torque sequence for installation., And 17 inches. Show ruler and 19 inches. Show size I/O port 18.5 inches. Guidelines for the Design and Construction of Externally Bonded FRP Systems for Strengthening Concrete Structures, Report of ACI Committee 440 ACI 440.2R-17, Size 10, was first printed in May 2017 ISBN: 978-1-945,487-59-0 Guidelines for the Design and Construction of Externally Bonded FRP Systems for Strengthening Concrete, American Concrete Institute, Farmington Hill, Michigan. All rights reserved. All rights reserved. This material may not be reproduced or reproduced in whole or in part in any print, mechanical, electronic, film or other distribution and storage media without the written consent of ACI. The Technical Committee responsible for ACI Committee reports and standards strives to avoid ambiguities, omissions and errors in these documents. Despite these efforts, users of ACI files occasionally find that information or requirements may require multiple interpretations, or may be incomplete or incorrect.
