MVME188A-4P工控備件模塊
如果根據EN1050的風險評估結果，自動重啟可能會產生風險，則不得使用該模式。參見EN 60204 Pt.1和EN954 Pt.1。對于手動復位模式，常開彈簧復位（非閉鎖）按鈕必須跨MC-MC端子連接，或與常閉接觸器串聯。當去除驅動力時，只有按下按鈕后，裝置才會工作?？刂茊卧姾?，還必須按下該按鈕。4.7與控制單元的外形連接這些端子用于將外形連接到：-Z1=棕色（內部導體）。Z2=白色（外部連接器）。參見5.3應用。注：配置文件必須以6K結尾? 串聯電阻（黃色）。當兩個外形直接連接到Z1和Z2（并聯）時，每個外形應使用15K電阻器（藍色）終止。并聯和串聯連接可選連接方法并聯連接最多可以并聯兩個型材，以幫助在某些應用中輕松布線。使用15K電阻器（藍色）串聯連接如果要使用多個配置文件，它們通常如圖所示串聯連接。使用6K8電阻器（黃色）15 12 4.0電氣連接-安全控制單元440F-C251P（表面安裝）440F-C2514D（導軌安裝）A1+Z2 MC 13 23 31 A2-Z1 MC 14 24 32 4.3 4.2 4.1 4.7 4.6 4.5 4.4電源保險絲500mA 110V 230V停止（紅色）打開（黃色）運行（綠色）4.1電源保險絲500mA安全保險絲2A 4.2 L 110V 230V N ve+--31 32 13 23 24 4.3 4.4 4.7 4.6停止紅色打開黃色LED指示燈運行綠色Z1 Z2 MC MC控制單元安裝和布線-（按照步驟4.1至4.7正確安裝）重要事項：布線必須符合國家電氣規范和適用的地方法規和條例4.1電源選擇開關如果使用110V AC或230V AC電源，則應在打開電源前適當設置電壓選擇開關。該裝置在制造時設置為230V AC。4.2電源輸入端子LN（A1、A2）如果使用110V AC或230V AC電源，則應將其與保護接地（接地）一起連接至所示端子。保護接地線的尺寸應至少等于電源線的尺寸。同時檢查（4.1）。
如果使用這些端子，則忽略（4.3）。4.3 24V AC/DC輸入端子+ve和-ve如果使用24V AC/DC電源，則應將電源連接到這些端子，確保觀察到正確的極性。不要與（4.2）的端子進行任何連接。如果使用24V AC或DC電源，則必須根據國際電氣安全規程（IEC 364-4-41）將其與主電源隔離。一個極應接地。對于24V DC，負極應接地（接地）。對于24V AC，電源的接地（接地）極應連接到-ve端子。4.4輔助輸出端子31和32該端子提供了一個輔助常閉觸點（即，當綠色“運行”燈熄滅時閉合），適用于指示或報警裝置。由于這是一個輔助設備，因此不得將其連接到安全電路。4.5安全輸出端子13、14、23和24這些是用于連接到機器安全電路的無電壓觸點，即它們與機器接觸器控制電路串聯連接。（250V AC時的最大額定值2A）。這兩個安全電路都有內部保險絲，但也必須使用2A快速熔斷器進行外部保護。如果使用一個接觸器，則需要端子13和24，端子14和23應跨接在一起。對于具有2個獨立控制電路（即雙通道系統）的2個接觸器，一個接觸器使用13-14，另一個接觸器采用23-24。對于2個接觸器，另請參見（5.3）。13文件控制編號：440F-CT001E-EN-E 1/2 EU合格產品聲明：安全墊控制器制造商名稱和地址：美國威斯康星州密爾沃基南二街1201號羅克韋爾自動化股份有限公司，郵編53204。授權代表的姓名和地址：羅克韋爾自動化公司Pegasus Park De Kleetlaan 12A 1831 Diegem Belgium本符合性聲明由制造商全權負責發布。聲明對象：Allen-Bradley/Guardmaster 440F-C系列（參考隨附的目錄號列表）上述聲明對象符合相關歐盟協調立法：2014/30/EU EMC指令（EMC）2006/42/EC機械指令（MD）2011/65/EU RoHS指令（RoHS）使用的相關協調標準或參考與符合性聲明相關的其他技術規范：EN ISO 13849-1:2015機械安全–控制系統的安全相關部件–第1部分：設計一般原則EN 13856-1:2013機械安全–壓敏保護裝置–
If according to the risk assessment results of EN1050, automatic restart may cause risks, this mode shall not be used. See EN 60204 Pt.1 and EN954 Pt.1. For manual reset mode, the normally open spring reset (non locking) button must be connected across the MC-MC terminal or in series with the normally closed contactor. When the driving force is removed, the device will not work until the button is pressed. This button must also be pressed when the control unit is powered on. 4.7 Connect with the profile of the control unit These terminals are used to connect the profile to: - Z1=brown (internal conductor). Z2=white (external connector). See 5.3 Application. Note: The configuration file must end with 6K ? series resistance (yellow). When two profiles are directly connected to Z1 and Z2 (in parallel), each profile shall be terminated with a 15K resistor (blue). Parallel connection and series connection Optional connection methods Parallel connection can be used to connect up to two profiles in parallel to facilitate easy wiring in some applications. Use 15K resistor (blue) to connect in series If multiple configuration files are to be used, they are usually connected in series as shown in the figure. Use 6K8 resistor (yellow) 15 12 4.0 electrical connection - safety control unit 440F-C251P (surface mount) 440F-C2514D (rail mount) A1+Z2 MC 13 23 31 A2-Z1 MC 14 24 32 4.3 4.1 4.7 4.5 4.4 Power fuse 500mA 110V 230V Stop (red) Open (yellow) Run (green) 4.1 Power fuse 500mA safety fuse 2A 4.2 L 110V 230V N ve+-- 31 32 13 23 24 4.3 4.4 4.7 4.6 Stop red, turn on yellow LED indicator light, run green, Z1 Z2 MC MC control unit installation and wiring - (correctly installed according to steps 4.1 to 4.7) Important: The wiring must comply with the national electrical specifications and applicable local laws and regulations 4.1 Power selection switch If 110V AC or 230V AC power supply is used, The voltage selector switch shall be set properly before turning on the power supply. The unit is set to 230V AC at the time of manufacture. 4.2 Power input terminals LN (A1, A2) If 110V AC or 230V AC power supply is used, it shall be connected to the terminals shown together with protective grounding (grounding). The size of the protective earth wire shall be at least equal to the size of the power line. Also check (4.1).
If these terminals are used, ignore (4.3). 4.3 24V AC/DC input terminals+ve and - ve If 24V AC/DC power supply is used, connect the power supply to these terminals to ensure correct polarity is observed. Do not make any connection with the terminal of (4.2). If 24V AC or DC power supply is used, it must be isolated from the main power supply according to the International Electrical Safety Code (IEC 364-4-41). One pole should be grounded. For 24V DC, the negative pole should be grounded (grounded). For 24V AC, the ground (ground) pole of the power supply should be connected to the - ve terminal. 4.4 Auxiliary output terminals 31 and 32 This terminal provides an auxiliary normally closed contact (that is, it is closed when the green "Run" light is off), which is suitable for indication or alarm devices. Since this is an auxiliary device, it must not be connected to a safety circuit. 4.5 Safety output terminals 13, 14, 23 and 24 are voltage free contacts used to connect to the machine safety circuit, that is, they are connected in series with the machine contactor control circuit. (Maximum rating 2A at 250V AC). These two safety circuits have internal fuses, but they must also be externally protected with 2A fast acting fuses. If a contactor is used, terminals 13 and 24 are required, and terminals 14 and 23 should be jumpered together. For two contactors with two independent control circuits (i.e. dual channel system), one contactor uses 13-14 and the other uses 23-24. For 2 contactors, see also (5.3). 13 Document control number: 440F-CT001E-EN-E 1/2 EU Declaration of conformity: name and address of safety pad controller manufacturer: Rockwell Automation Co., Ltd., 1201 South Second Street, Milwaukee, Wisconsin 53204, United States. Name and address of the authorized representative: Pegasus Park De Kleetlaan 12A 1831 Diego Belgium, Rockwell Automation. The manufacturer is solely responsible for issuing this declaration of conformity. Declared object: Allen Bradley/Guardmaster 440F-C series (refer to the attached catalog number list) The above declared object complies with the relevant EU harmonized legislation: 2014/30/EU EMC Directive (EMC) 2006/42/EC Machinery Directive (MD) 2011/65/EU RoHS Directive (RoHS) Relevant harmonized standards used or other technical specifications related to the declaration of conformity referred to: EN ISO 13849-1:2015 Safety of machinery - Safety related components of control systems - Part 1: General principles of design EN 13856-1:2013 Safety of machinery - Pressure sensitive protective devices -
