MVME172PA-642SE工控卡件
安裝后，應將本手冊保存在安全且可接近的地方。如需進一步幫助，請聯系供應商。第1節-儲存和搬運1.1儲存控制裝置和墊傳感器應儲存在-40°C至+70°C的溫度范圍內。墊子傳感器應垂直存放。1.2搬運和運輸控制裝置和墊傳感器應在-40°C至+70°C的溫度范圍內運輸。應使用原始包裝或類似包裝，必要時應加固，以防止損壞和彎曲。始終小心打開包裝，避免被刀具等損壞。當傳感器墊移動到位時，切勿通過其連接線拉動或提起傳感器。對于較大的傳感器墊，需要兩個人才能安全起吊并防止傳感器墊因過度彎曲而損壞。4第2節-系統描述系統包括一個或多個互連的壓敏墊和一個控制單元。檢測區域內沒有“死區”。單個傳感器墊部分有矩形標準尺寸，也有特殊切割形狀，最大尺寸為最大標準墊。
所有傳感器墊具有相同的結構和操作原理。每個墊子都有兩個導電板，它們由非導電的可壓縮隔板隔開。這些墊子在24V DC下工作，并串聯在一起，以形成機器周圍危險區域的地面感應系統。通過墊的電路由控制單元監控，當區域空閑時，控制單元向機器控制電路提供信號。當踏上任何墊子時，導電板接觸，電路中的電阻下降。這由關閉機器的控制單元監控。將檢測到墊、接線或控制單元中的任何單個電氣故障，并且控制單元輸出將進入安全（OFF）狀態。模制乙烯基傳感器墊密封至IP 67.440F-C28013控制單元。該單元包括一個八通道傳感墊系統。當踩下任何墊子時，控制單元將關閉機器，并在CHANNEL FAULT STATUS（信道故障狀態）顯示屏上顯示正在操作的墊子。有兩種操作模式：手動復位和自動復位。在手動復位模式下，輸出“ON”信號只能在移除驅動力并復位后恢復。
After installation, keep this manual in a safe and accessible place. For further assistance, please contact the supplier. Section 1 - Storage and Handling 1.1 Storage controls and pad sensors shall be stored in a temperature range of - 40 ° C to+70 ° C. Cushion sensors should be stored vertically. 1.2 The handling and transportation control devices and pad sensors shall be transported within the temperature range of - 40 ° C to+70 ° C. The original packaging or similar packaging shall be used, and if necessary, it shall be reinforced to prevent damage and bending. Always open the package carefully to avoid being damaged by knives, etc. When the sensor pad moves in place, do not pull or lift the sensor through its connecting wire. For larger sensor pads, two people are required to lift safely and prevent damage to the sensor pads due to excessive bending. 4 Section 2 - System Description The system consists of one or more interconnected pressure sensitive pads and a control unit. There is no "dead zone" in the detection area. The single sensor pad has rectangular standard size and special cutting shape. The maximum size is the maximum standard pad.
All sensor pads have the same structure and operating principle. Each cushion has two conductive plates, which are separated by non-conductive compressible partitions. These pads work at 24V DC and are connected in series to form a ground sensing system in the hazardous area around the machine. The circuit through the pad is monitored by the control unit, which provides signals to the machine control circuit when the area is free. When stepping on any mat, the conductive plate contacts and the resistance in the circuit decreases. This is monitored by the control unit that shuts down the machine. Any single electrical fault in the pad, wiring or control unit will be detected, and the control unit output will enter the OFF state. Molded vinyl sensor gasket seals to IP 67.440F-C28013 control unit. The unit includes an eight channel sensing pad system. When any mat is depressed, the control unit shuts down the machine and displays the mat being operated on the CHANNEL FAULT STATUS display. There are two operation modes: manual reset and automatic reset. In the manual reset mode, the output "ON" signal can only be restored after the driving force is removed and reset.
