MVME172P-644LSE工控備件機器人模塊
該系統允許操作員和某些類型的車輛清晰地查看過程，不受阻礙地進入。必須有足夠的空間，以確保從危險區到可接近的墊子周邊的最小距離符合第5節中給出的安全距離計算。所定義的周邊和危險區之間的整個地面區域必須由墊子傳感器覆蓋，以便在不啟動墊子系統的情況下無法接近或接近危險區。危險墊8用作防護周界內的存在感測系統圖6用作防護周界中的存在感系統。該系統提供存在感測，以防止人員在封閉區域內時機器啟動的任何可能性。當系統以這種方式用作二級保護系統時，第5.4.1節中給出的安全距離計算不適用。周界防護方法應符合所有相關要求。封閉周界和危險區域之間的整個地面區域必須由墊子傳感器覆蓋，以便人員在不啟動墊子系統的情況下無法進入封閉區域。危險壓力敏感墊固定防護聯鎖門（帶鎖）9第4節-規范控制單元440F-C4000P 440F-C400S 440F-C4000 D符合EN 1760-1、EN 60204-1、EN 954-1：3類，UL 508響應時間（墊子按壓-35mS安全觸點打開）環境保護IP65 NEMA12外殼-IP40 DIN0470端子-IP20 DIN0470脈沖耐受電壓2500V污染等級III最小開關電流/電壓10mA/10V電源-用戶選擇110/230V AC（50-60Hz）和24V AC/DC+10%-15%（110V設置也允許在100v±10%下使用）
功耗<9 VA 6W繼電器輸出2個獨立的無電壓N/O安全觸點1個無電壓N/C輔助觸點NB-Aux不得用于外部安全電路保險絲，AC最大5A（快速作用），AC最大2.5A（快速作用的），DC使用類別AC-15；4A/250V交流-直流-13；2A/30V DC輸出：遠程復位/指示燈24V DC/0.24W輸入遠程復位開關（2 x N/O）安全輸入4線墊指示燈LED 1電源綠色LED 2自動復位模式綠色LED 3手動復位模式綠色LED4機器啟用綠色內部控制交流電壓選擇器，自動/手動復位選擇器內部電源保險絲500mA可更換500mA可替換500mA可換（2個）（2個關閉）（1個關閉）500mA可重置（1個）工作溫度范圍-10°C至+45°C濕度在+50°C時敢達90%RH根據IEC 68-2-6進行振動測試，頻率范圍10-55Hz，每軸位移0.15mm 10個周期，掃描速率，每分鐘1倍頻程MC-MC接觸器監控回路常閉接觸器回路最大導線尺寸為1 x 1.5mm2絞合1 x 1.5mmm2絞合2 x 1.5mm2，套管剝離，套管剝離5mm，1 x 2.5mm2 5mm，1×2.5mm2 8mm，2 x 2.5mm2實心導體實心導體端子負端子正/負固定螺釘M2.5
The system allows the operator and certain types of vehicles to see the process clearly and enter unhindered. There must be sufficient space to ensure that the minimum distance from the danger zone to the perimeter of the accessible mat complies with the safety distance calculation given in Section 5. The entire ground area between the defined perimeter and the hazard area must be covered by a mat sensor so that the hazard area cannot be approached or approached without activating the mat system. The hazard pad 8 is used as a presence sensing system within the protective perimeter Figure 6 is used as a presence sensing system within the protective perimeter. The system provides presence sensing to prevent any possibility of the machine starting when a person is in an enclosed area. When the system is used as a secondary protection system in this way, the safety distance calculation given in Section 5.4.1 is not applicable. The method of perimeter protection shall comply with all relevant requirements. The entire ground area between the enclosed perimeter and the hazardous area must be covered by mat sensors so that personnel cannot enter the enclosed area without activating the mat system. Dangerous pressure sensitive pad fixed protective interlocking door (with lock) 9 Section 4 - Specification Control unit 440F-C4000P 440F-C400S 440F-C4000 D according to EN 1760-1, EN 60204-1, EN 954-1:3, UL 508 response time (cushion pressing - 35mS safety contact opens) Environmental protection IP65 NEMA 12 housing - IP40 DIN0470 terminal - IP20 DIN0470 pulse withstand voltage 2500V Pollution level III Minimum switching current/voltage 10mA/10V power supply - user selects 110/230V AC (50-60Hz) and 24V AC/DC+10% - 15% (110V setting is also allowed to be used under 100v ± 10%)
Power consumption<9 VA 6W relay outputs 2 independent voltage free N/O safety contacts 1 voltage free N/C auxiliary contact NB Aux shall not be used for external safety circuit fuses, AC maximum 5A (fast acting), AC maximum 2.5A (fast acting), DC use category AC-15; 4A/250V AC-DC-13; 2A/30V DC output: remote reset/indicator light 24V DC/0.24W input remote reset switch (2 x N/O) safety input 4 wire pad indicator light LED 1 power supply green LED 2 automatic reset mode green LED 3 manual reset mode green LED 4 machine enable green internal control AC voltage selector, Automatic/manual reset selector internal power fuse 500mA replaceable 500mA replaceable 500mA replaceable (2) (2 off) (1 off) 500mA resettable (1 off) Operating temperature range - 10 ° C to+45 ° C Humidity at+50 ° C dare to reach 90% RH Vibration test according to IEC 68-2-6, frequency range 10-55Hz, displacement of each shaft 0.15 mm 10 cycles, scanning rate, One octave per minute MC-MC contactor monitoring circuit Normally closed contactor circuit Maximum conductor size is 1 x 1.5mm2 stranded 1 x 1.5mm2 stranded 2 x 1.5mm2, casing stripping, casing stripping 5mm, 1 x 2.5mm2 5mm, 1 × 2.5mm2 8mm, 2 x 2.5mm2 solid conductor solid conductor terminal negative terminal positive/negative fixing screw M2.5
