MVME172-432工控自動化卡件
任一接線通道中的單一故障將導致墊子控制單元鎖定安全輸出，直到故障得到糾正并重置控制單元。檢查系統中的所有連接導線是否正確配置且未損壞，兩個接觸器是否正常工作。排除所有故障，如果處于手動復位模式，則按下并釋放控制單元復位按鈕。4.如果問題未得到解決，請聯系供應商。38 8.5.2癥狀–機器無法停止或可以在墊子上啟動。不允許使用機器1。如果墊子上有機器，墊子控制單元上的機器啟用LED是否點亮？2.如果MACHINE ENABLED LED（機器啟用LED）未亮起，則機器或其控制系統在墊系統外部可能存在故障。–在排除和測試故障之前，不得使用機器。3.如果機器啟用LED亮起。-不允許使用機器，并立即聯系供應商。8.5.3癥狀–機器在傳感器墊上不存在的情況下意外停止，但可以在踩下墊后重新啟動（并在手動重置模式下重置）。1.檢查所有指示燈是否正常工作。如果是這樣的話，問題很可能是由某個值和持續時間的供電下降引起的。這可能會導致控制單元中的一個內部繼電器斷開，從而模擬故障狀況。這是極不可能發生的情況，不需要采取補救措施。在問題持續存在的異常情況下，可能需要采取措施以確保向墊子系統提供更順暢的電源。8.6維修在墊系統或機器控制系統上工作之前，隔離機器和墊系統的電源。
遵守電氣安全預防措施。用戶維修僅限于更換新的墊系統部件。如果出現問題，應將裝置退還給供應商。應使用推薦的對接拼接接頭對連接線進行任何維修。篡改零部件將使保修失效。如果DIN導軌控制單元上的質量封條損壞，則保修無效。39可用備件對于特殊尺寸的傳感器墊，請參閱標簽上打印的型號。更換任何零件后，必須進行8.2所示的檢查和測試，并特別注意更換的零件。警告：維護或維修操作后，必須正確重新安裝所有鑲邊、緊固件和電纜保護裝置。不這樣做或使用未經批準的零件或修改可能導致墊子系統無法達到其規定性能。8.7服務如需服務和協助，請聯系供應商。尺寸型號。周邊裝飾指定長度MGT 3010兩件式周邊裝飾指定長MGT 3011（帶電纜干線）單元裝飾指定長MG T 3020保護導線導管指定長MGG 3030 Mat控制單元MGCP1 MGCS1 MGCD1 MGCSM1與MGCD1系統備件套件描述零件號2保險絲500mA（T）TR5 4對接拼接連接器傳感器墊1000mm x 1250mm MGM2025傳感器墊1000mm x 1500mm MGM 2030 40長度目錄號。標準周邊飾件2M 440F-T3210標準周邊飾件3M 440F-T3310標準周邊內飾5M 440F-T3510外角標準周邊飾件440F-T3012內角標準周邊內飾440F-T3013帶電纜通道2M 440F-13211帶電纜通道4M 440F-T3411外角周邊飾件
A single fault in any wiring channel will cause the mat control unit to lock the safety output until the fault is corrected and the control unit is reset. Check whether all connecting wires in the system are correctly configured and undamaged, and whether the two contactors work normally. Eliminate all faults. If it is in the manual reset mode, press and release the control unit reset button. 4. If the problem is not solved, please contact the supplier. 38 8.5.2 Symptoms - The machine cannot be stopped or can be started on the mat. Machine 1 is not allowed. If there is a machine on the mat, does the machine enable LED on the mat control unit illuminate? 2. If the MACHINE ENABLED LED is not lit, the machine or its control system may have a fault outside the cushion system. – Do not use the machine until the problem has been corrected and tested. 3. If the machine enable LED lights up- Do not use the machine and contact the supplier immediately. 8.5.3 Symptoms - The machine stops unexpectedly when the sensor pad is not present, but can be restarted after the pad is depressed (and reset in manual reset mode). 1. Check whether all indicators work normally. If so, the problem is likely to be caused by a drop in power supply for a certain value and duration. This may cause an internal relay in the control unit to open, simulating a fault condition. This is a highly unlikely situation and does not require remedial measures. In abnormal situations where the problem persists, measures may need to be taken to ensure a smoother power supply to the mat subsystem. 8.6 Before maintenance works on the cushion system or machine control system, isolate the power supply of the machine and the cushion system.
Observe electrical safety precautions. User repair is limited to replacing new gasket system components. In case of problems, the unit shall be returned to the supplier. Any repairs to the connecting wires shall be made using the recommended butt splice joints. Tampering parts will void the warranty. If the quality seal on the DIN rail control unit is damaged, the warranty is invalid. 39 Spare Parts Available For special size sensor pads, refer to the model number printed on the label. After any part is replaced, the inspection and test as shown in 8.2 must be carried out, and special attention must be paid to the replaced parts. WARNING: All trim, fasteners, and cable protectors must be properly reinstalled after maintenance or repair operations. Failure to do so or the use of unapproved parts or modifications may result in the mat subsystem not achieving its specified performance. 8.7 Service If you need service and assistance, please contact the supplier. Size and model. Specified length of peripheral decoration MGT 3010 two-piece peripheral decoration Specified length MGT 3011 (with cable trunk) Unit decoration Specified length MG T 3020 Protective conductor conduit Specified length MGG 3030 Mat Control unit MGCP1 MGCS1 MGCD1 MGCSM1 and MGCD1 System spare parts kit Description Part No. 2 Fuse 500mA (T) TR5 4 Butt splice connector Sensor pad 1000mm x 1250mm MGM2025 Sensor pad 1000mm x 1500mm MGM 2030 40 Length Catalog No. Standard Perimeter Trim 2M 440F-T3210 Standard Perimeter Trim 3M 440F-T3310 Standard Perimeter Trim 5M 440F-T3510 Exterior Corner Standard Perimeter Trim 440F-T3012 Interior Corner Standard Perimeter Trim 440F-T3013 With Cable Channel 2M 440F-13211 With Cable Channel 4M 440F-T3411 Exterior Corner Perimeter Trim
