MVME172-343模塊備件
注意：如果接觸器卡在ON位置，則當墊處于ON位置時，電機不會停止。圖16顯示了兩個接觸器和接觸器監控（雙通道）440F-4000P和440F-C4000S的應用連接圖示例。電路狀態-電源打開-傳感器墊上不存在-復位按鈕已操作（如果處于手動復位模式）-機器啟動電路已啟用。注意：如果任何一個接觸器卡在ON（接通）位置，則當墊放在上面時，電機將停止，并檢測到故障。M K1 K2 24VDC，電源L1 L2 L3輔助輸出輔助輸入K1（AUX）K2（au）啟動瞬時按鈕停止瞬時按鈕熔斷器電機保護，例如熱斷路器12 3 4+VE 31 13 23 MC MC 32 14 24控制單元K1 K2-VE正向引導接觸器輔助觸點L N110VAC，230VAC電源（備用電源連接）白色-白色-黑色-黑色傳感器墊內部傳感器墊板N/O PB R IND M K1 24VDC，電源L1 L2 L3輔助輸出輔助輸入K1（輔助）啟動瞬時按鈕停止瞬時按鈕保險絲電機保護，例如。熱斷路器12 3 4 MC MC+VE控制單元K1–VE白-白-黑-黑傳感器墊內部傳感器墊板L N鏈路31 13 23 N/O PB R IND 32 14 24 110VAC，230VAC電源（備用電源連接）22圖17顯示單接觸器（單通道）440F-C4000D應用的連接圖示例。電路狀態-電源打開-傳感器墊上不存在-復位按鈕已操作（如果處于手動復位模式）-機器啟動電路已啟用。注意：如果接觸器卡在ON位置，則當墊處于ON位置時，電機不會停止。圖18顯示了兩個接觸器和接觸器監控（雙通道）440F-C4000D應用的示例連接圖。
電路狀態-電源打開-傳感器墊上不存在-復位按鈕已操作（如果處于手動復位模式）-機器啟動電路已啟用。注意：如果任何一個接觸器卡在ON（接通）位置，則電機將在墊放置時停止，并檢測到故障。M K1 K2 24VDC，電源L1 L2 L3輔助輸出輔助輸入K1（AUX）K2（auux）啟動瞬時按鈕停止瞬時按鈕熔斷器電機保護，例如熱斷路器12 3 4+31 MC MC 13 23 32 14 24控制單元K1 K2-正導接觸器輔助觸點A1 A2白-白-黑-黑-風傳感器墊內部傳感器墊板Y2 Y4 Y6復位IND Y1 Y3 Y5 110VAC，230VAC電源（備用電源連接）M K1 24VDC，電源L1 L2 L3輔助輸出輔助輸入K1（輔助）啟動瞬時按鈕停止瞬時按鈕熔斷器電機保護，例如熱斷路器12 3 4 MC+控制單元K1–白-白-黑-黑傳感器墊內部傳感器墊A1 A2鏈接31 13 23 Y2 Y4 Y6重置IND 32 14 24 Y1 Y3 Y5 MC 110VAC，230VAC電源（備用電源連接）23安全相關控制系統設計完成后，確保5.4.1中假設的響應時間保持有效。如果值發生變化，則需要重復安全距離計算。接下來考慮重置選項。在正常條件和故障條件下，應仔細考慮所選重置方案的后果，以防意外啟動等造成的危險。下面給出了墊子系統兩種模式的時序圖。圖19手動復位模式圖20自動復位模式驅動、復位和輸出之間的關系。啟動和輸出手動復位模式之間的關系可通過控制單元上的按鈕或遠程按鈕或機器安全相關控制系統內的無電壓觸點實現復位。系統的輸出將保持關閉，直到通電后復位，并且在存在其他通電聯鎖（啟動聯鎖）的復雜系統中可能需要主/從復位電路。自動復位模式當在自動復位模式下使用時，機器的控制系統將需要一個單獨的復位功能，以防止機器在離開墊子或臨時電源故障或下降后啟動。
Note: If the contactor is stuck in the ON position, the motor will not stop when the pad is in the ON position. Figure 16 shows the application connection diagram example of two contactors and contactor monitoring (dual channel) 440F-4000P and 440F-C4000S. Circuit status - power on - not present on sensor pad - reset button operated (if in manual reset mode) - machine start circuit enabled. Note: If any contactor is stuck in the ON position, the motor will stop and a fault will be detected when the pad is placed on it. M K1 K2 24VDC, power supply L1 L2 L3 auxiliary output auxiliary input K1 (AUX) K2 (au) start instantaneous button stop instantaneous button fuse motor protection, such as thermal circuit breaker 12 3 4+VE 31 13 23 MC MC 32 14 24 control unit K1 K2-VE forward guiding contactor auxiliary contact L N110VAC, 230VAC power supply (standby power connection) white white black sensor pad internal sensor pad N/O PB R IND M K1 24VDC, Power supply L1 L2 L3 auxiliary output auxiliary input K1 (auxiliary) start instantaneous button stop instantaneous button fuse motor protection, for example. Thermal circuit breaker 12 3 4 MC MC+VE control unit K1 – VE white white black black sensor pad Internal sensor pad L N link 31 13 23 N/O PB R IND 32 14 24 110VAC, 230VAC power supply (standby power supply connection) 22 Figure 17 shows an example of connection diagram for single contactor (single channel) 440F-C4000D application. Circuit status - power on - not present on sensor pad - reset button operated (if in manual reset mode) - machine start circuit enabled. Note: If the contactor is stuck in the ON position, the motor will not stop when the pad is in the ON position. Figure 18 shows an example connection diagram for two contactors and contactor monitoring (dual channel) 440F-C4000D applications.
Circuit status - power on - not present on sensor pad - reset button operated (if in manual reset mode) - machine start circuit enabled. Note: If any of the contactors is stuck in the ON position, the motor will stop when the pad is placed and a fault is detected. M K1 K2 24VDC, power supply L1 L2 L3 auxiliary output auxiliary input K1 (AUX) K2 (auux) start instantaneous button stop instantaneous button fuse motor protection, such as thermal circuit breaker 12 3 4+31 MC MC 13 23 32 14 24 control unit K1 K2 positive contactor auxiliary contact A1 A2 white black wind sensor pad internal sensor pad Y2 Y4 Y6 reset IND Y1 Y3 Y5 110VAC, 230VAC power supply (standby power connection) M K1 24VDC, Power supply L1 L2 L3 auxiliary output auxiliary input K1 (auxiliary) start instantaneous button stop instantaneous button fuse motor protection, such as thermal circuit breaker 12 3 4 MC+control unit K1 – white white black sensor pad internal sensor pad A1 A2 link 31 13 Y2 Y4 Y6 reset IND 32 14 Y1 Y3 Y5 MC 110VAC, 230VAC power supply (standby power connection) 23 After the design of safety related control system is completed, Ensure that the response time assumed in 5.4.1 remains valid. If the value changes, the safety distance calculation needs to be repeated. Next consider the reset option. Under normal and fault conditions, the consequences of the selected reset scheme should be carefully considered to prevent the danger caused by accidental startup, etc. The time sequence diagrams of the two modes of the cushion subsystem are given below. Fig. 19 Manual reset mode Fig. 20 Relationship between automatic reset mode drive, reset and output. The relationship between the start and output manual reset modes can be reset via a button or remote button on the control unit or a voltage free contact in the machine safety related control system. The output of the system will remain closed until reset after power on, and the master/slave reset circuit may be required in complex systems with other power on interlocks (start interlocks). Automatic reset mode When used in the automatic reset mode, the control system of the machine will need a separate reset function to prevent the machine from starting after leaving the mat or after a temporary power failure or drop.
