MVME162PA-242LSE備件庫存
不屬于自動化的商標是其各自公司的財產。年月版權所有? .保留所有權利。美國印刷。取代 年月產品規格目錄編號描述 功率表指示器 電量表 交流 脈沖數字輸出 電源表交流 交流交流模擬輸出 功率計 串行功率計 氰基丙烯酸酯粘合劑確保持久密封和高防護等級達到。.安裝軌道軌電纜連接器，將蓋子封閉到控制單元或下一個帶電阻器的型材連接器 維修在系統或機器控制系統上工作前，將電源與機器和系統隔離。遵守電氣安全預防措施。用戶維修僅限于更換新的系統部件。如果出現任何問題，應將裝置退還給供應商。應使用熱縮對接接頭對連接線進行任何維修。更換任何零件后，必須對更換的零件進行和所示的檢查和測試，并特別注意。篡改零部件將使保修失效。如果導軌控制單元上的質量密封損壞，則保修無效警告維護或維修操作后，必須正確重新安裝所有緊固電纜保護裝置。未能做到這一點或使用未經批準的部件可能會導致系統無法達到其規定的性能。安裝型導軌.安全型材的組裝和安裝將安全型材切割成一定長度。無滑行室的型材應使用橡膠剪進行切割。帶有滑行室的型材應使用細齒鋸切割。安裝時鉆孔未提供緊固件 型材清潔型材應保持無沉積物，如切屑和其他材料，以防止損壞或死區。
Trademarks that are not automatic are the property of their respective companies. Copyright ? . All rights reserved. Printed in the USA. Replace the product specification catalog number of the month and year Description of power meter Indicator of power meter AC pulse digital output power meter AC AC analog output power meter Serial power meter Cyanoacrylate adhesive ensures durable sealing and high protection level Install the rail cable connector, close the cover to the control unit or the next profile connector with resistor, and isolate the power supply from the machine and the system before working on the system or machine control system. Observe electrical safety precautions. User maintenance is limited to replacing new system components. In case of any problems, the unit shall be returned to the supplier. Any repairs to the connecting wires shall be made using heat shrinkable butt joints. After any parts are replaced, the replaced parts must be inspected and tested as shown in and with special attention. Tampering parts will void the warranty. If the quality seal on the rail control unit is damaged, the warranty is invalid WarningAfter maintenance or repair operations, all fastening cable protectors must be reinstalled correctly. Failure to do so or the use of unapproved components may cause the system to fail to achieve its specified performance. Mounting type guide rail The assembly and installation of the safety profile cut the safety profile into a certain length. The profile without sliding chamber shall be cut with rubber shear. Sections with sliding chambers shall be cut with a fine tooth saw. When installing, the drilling does not provide fasteners. The cleaning profile should be kept free of sediment, such as chips and other materials, to prevent damage or dead zones.
