MVME162P-344工控自動化卡件
標簽也可以在設備上或內部，以提供特定的預防措施。警告確定在危險環境中可能導致爆炸的做法或情況的信息，這可能導致人身傷害或財產損失或經濟損失。在手動復位模式下，輸出信號只能在移除驅動力并復位后恢復。手動復位通過按下和釋放蓋上安裝的控制單元復位按鈕或遠程安裝的按鈕來實現。在通電或斷電后以及隨后恢復電源后，輸出將“關閉”，直到收到復位信號，即使墊子未啟動。在自動復位模式下，僅通過移除驅動力來實現輸出信號。對于這兩種模式，在啟動墊子后，安全觸點將始終處于斷開狀態。第節將更詳細地介紹模式選擇。各個傳感器墊通過根電線相互連接并連接到控制單元?？刂茊卧哂薪徊姹O(jiān)控的安全繼電器，可以配置該單元，以便檢測到外部接觸器故障?？刂茊卧姎夤收戏系陬惖囊螅瑱C(jī)器控制系統的相關部分也能滿足。墊子傳感器符合第類的要求。第節詳細介紹了接口。墊子的工作原理如圖所示。圖當墊子被激活時，不導電的可壓縮隔板顯示為黑色壓縮到其凹槽中，允許兩個板進行接觸，從而提供全部靈敏度。該系統旨在檢測體重為或以上的成年人。它適用于檢測使用助行器手杖或框架的成年人。該系統不適合檢測兒童。該系統不得與墊上的任何額外覆蓋物一起使用。墊在靜止的鋼板上模制乙烯基墊激活。墊的乙烯基外表面完全密封，以防止液體進入。它能抵抗漂白酸鹽和大多數工業化學品。未經自動化股份有限公司書面許可，嚴禁復制本手冊的全部或部分內容。在本手冊中，我們會在必要時使用注釋，以提醒您注意安全事項。有關耐化學性的詳細指南，請參閱第節。系統在下運行，故障電流受限。因此，在正常情況下，墊或互連線路的損壞不會產生任何電擊危險。圖基本系統和連接用兩個接觸器顯示。和。注復位按鈕的位置與上的位置不同。電源端子電源端子手動復位自動復位開關輔助保險絲主保險絲選擇開關蓋安裝復位按鈕控制單元編號+指示器遠程復位端子遠程復位指示端子接觸器監控端子輔助端子安全輸出端子墊連接端子機器啟用綠色自動復位模式綠色手動復位模式綠色電源綠色傳感器墊接觸器控制電源無電壓輔助。
Labels can also be on or inside the equipment to provide specific precautions. Warning Information that identifies practices or situations that could lead to an explosion in a hazardous environment, which could result in personal injury or property damage or economic loss. In the manual reset mode, the output signal can only be restored after the driving force is removed and reset. Manual reset is achieved by pressing and releasing the control unit reset button installed on the cover or the remote installed button. After power on or power off and subsequent power restoration, the output will "turn off" until a reset signal is received, even if the mat is not started. In the automatic reset mode, the output signal is achieved only by removing the driving force. For both modes, the safety contact will always be disconnected after starting the mat. Section describes mode selection in more detail. The sensor pads are connected to each other and to the control unit via a wire. The control unit has a cross monitored safety relay, which can be configured to detect external contactor faults. The electrical failure of the control unit meets the requirements of Category, and the relevant parts of the machine control system can also meet the requirements. The cushion sensor meets the requirements of category. Section describes the interface in detail. The working principle of the mat is shown in the figure. Figure When the mat is activated, the non-conductive compressible partition is shown as black compressed into its groove, allowing two plates to contact, thus providing full sensitivity. The system is designed to detect adults weighing or above. It is suitable for detecting adults using walking aid canes or frames. The system is not suitable for detecting children. The system shall not be used with any additional covering on the mat. The pad is activated by a molded vinyl pad on a stationary steel plate. The vinyl outer surface of the gasket is completely sealed to prevent liquid ingress. It is resistant to bleaches and most industrial chemicals. Without the written permission of Automation Co., Ltd., it is strictly forbidden to copy all or part of this manual. In this manual, we will use notes when necessary to remind you of safety precautions. Refer to Section for detailed guidance on chemical resistance. The system operates under and the fault current is limited. Therefore, under normal conditions, damage to the mat or interconnecting circuit does not create any electrical shock hazard. Figure Basic system and connections are shown with two contactors. And. Note The position of the reset button is different from that on the. Power terminal Power terminal Manual reset Automatic reset switch Auxiliary fuse Main fuse Selection switch Cover installation Reset button Control unit number+Indicator remote reset terminal Remote reset indication terminal Contactor monitoring terminal Auxiliary terminal Safety output terminal pad Connection terminal Machine enable green Automatic reset mode Green power Green sensor pad Contactor control power supply No voltage assistance.
