MVME162P-252SE機器人備件
對酮和大多數酯的耐受性較弱。注意化學品的組合可能會產生不可預測的影響。在這種情況下，建議進行測試。若需要測試，供應商可提供小塊乙烯基材料。打滑絆倒危險在大多數情況下，兩種傳感器墊模式都提供防滑表面，但應保持無大量油脂肥皂或凝膠沉積物。如果直的肋骨側是上臂，建議肋骨越過危險部位，以提高抓地力。磨損和損壞墊子外表面可能因尖銳或重物的沖擊而損壞。每次此類事件后，應檢查墊子是否變形或穿孔，必要時應更換。墊子經過設計和測試，可以在任何一個地方承受一百萬次操作。在使用中，不應超過任何單個位置的操作數。偶爾的重載如噸卡車不太可能損壞墊子，但不應在通過路線的交通中使用。爆炸性環境該系統不適用于爆炸性環境。墊子系統符合歐洲指令的要求。確保了在工業環境中可能出現的干擾條件下的正常操作，并已通過測試和認證。注當出現異常高水平的電磁干擾時，可能需要采取特殊措施，例如靠近焊接或感應加熱設備或靠近無線電發射器。地板傳感器墊的地板或安裝表面必須光滑且堅硬，即在預計的最重負載下沒有明顯變形。波動突出大間隙或其他不規則現象將增加傳感器墊的靈敏度，并可能導致間歇性意外關閉有害跳閘。圖墊子的地板狀況?？山邮苄《?guī)則的突起，如棋盤圖案。脫脂混凝土地板是理想的。如果有任何疑問，請聯系供應商?？刂茊卧惭b參考圖第節控制單元不得安裝在檢測區域內。如果手動復位或常規指示器觀察需要接近控制單元，則應將其安裝在保護區外的可接近位置，以提供危險和保護區的良好視野。
The tolerance to ketones and most esters is weak. Note that combinations of chemicals may have unpredictable effects. In this case, testing is recommended. If testing is required, the supplier can provide small pieces of vinyl material. Slipping and tripping hazard In most cases, both sensor pad modes provide a non slip surface, but should be kept free of large amounts of grease, soap or gel deposits. If the straight rib side is the upper arm, it is recommended that the rib cross the dangerous part to improve the grip. Wear and damage The outer surface of the mat may be damaged by sharp or heavy impact. After each such event, the mat shall be checked for deformation or perforation and replaced if necessary. The cushion is designed and tested to withstand a million operations anywhere. In use, the operands of any single position shall not be exceeded. Occasional heavy loads such as ton trucks are unlikely to damage the mat, but should not be used in traffic passing the route. Explosive atmospheres This system is not suitable for explosive atmospheres. The mat subsystem complies with the requirements of the European Directive. It ensures normal operation under possible interference conditions in industrial environment, and has passed the test and certification. Note When an abnormally high level of electromagnetic interference occurs, special measures may be required, such as being close to welding or induction heating equipment or radio transmitters. The floor or mounting surface of the floor sensor mat must be smooth and hard, that is, there is no obvious deformation under the expected heaviest load. Fluctuations highlighting large gaps or other irregularities will increase the sensitivity of the sensor pads and may cause intermittent accidental closure of harmful trips. Figure Floor condition of mat. Small and regular protrusions, such as chessboard patterns, are acceptable. Degreasing concrete flooring is ideal. If you have any questions, please contact the supplier. The control unit shall not be installed in the detection area as shown in Section of the installation reference drawing. If manual reset or conventional indicator observation requires access to the control unit, it shall be installed in an accessible position outside the protected area to provide a good view of the danger and the protected area.
