MVME162-523工控機器人備件
目視檢查電機有無損壞。檢查電機框架前輸出軸和安裝導向器是否有任何缺陷。立即通知承運人任何運輸損壞。保留原始包裝材料，以防您需要將產品退回維修或運輸?shù)狡渌恢?。使用?nèi)包裝箱和外包裝箱為單位退貨提供足夠的保護用于維修。在第頁規范中列出的環境條件下，將電機存放或操作在清潔干燥的地方。取下軸蓋用手取下安裝在電機軸上的保護蓋或用螺絲刀撬開蓋。不要使用錘子或其他工具，因?yàn)樗鼈儠?huì)損壞電機軸。注意為避免人身傷害和電機損壞，請勿通過電機軸提升或搬運電機。軸上的蓋子可能松動，導致電機掉落。注意不要試圖打開和修改電機。本手冊介紹了可在現場進行的修改。請勿執行本手冊中未描述的修改。只有授權的維修中心才能維修此項目。請參閱支持部門以獲取查找最近維修中心的幫助。系列或更小框架尺寸的低慣量無刷伺服電機年月延長電機壽命適當?shù)脑O(shè)計和維護可以延長伺服電機的壽命。遵循這些準則，以最大限度地延長伺服電機在您環境中的使用壽命始終在每條電纜中提供滴水環，以將液體從電機連接處帶走。如果可能，提供防護罩，以保護電機外殼軸封及其連接處免受異物或液體污染。軸封容易磨損，需要定期檢查和更換。根據使用情況，建議每個月更換一次，但不超過個月。有關更多信息，請參閱第頁的軸封套件。定期檢查電機和密封件有無損壞或磨損。如果發現損壞或過度磨損，請更換該部件。該伺服電機上的制動器選項是一個彈簧組保持制動器，當向制動線圈施加電壓時，該制動器會釋放。分離制動器需要單獨的電源。該電源可以通過伺服電機控制器或手動操作員控制來施加。
Visually inspect the motor for damage. Check the motor frame front output shaft and mounting guide for any defects. Notify the carrier immediately of any transport damage. Keep the original packaging materials in case you need to return the product for repair or transport to another location. Use inner and outer packing boxes to provide adequate protection for unit returns for maintenance. Store or operate the motor in a clean and dry place under the environmental conditions listed in the specifications on page. Remove the shaft cover Remove the protective cover installed on the motor shaft by hand or pry off the cover with a screwdriver. Do not use hammers or other tools as they will damage the motor shaft. To avoid personal injury and motor damage, do not lift or handle the motor through the motor shaft. The cover on the shaft may be loose, causing the motor to fall. Be careful not to attempt to open and modify the motor. This manual describes the modifications that can be made on site. Do not perform modifications not described in this manual. Only authorized service centers can repair this item. Refer to Support for help finding the nearest service center. Series or smaller frame size low inertia brushless servo motor can prolong the service life of the motor. Proper design and maintenance can prolong the service life of the servo motor. Follow these guidelines to maximize the service life of the servo motor in your environment Always provide a drip loop in each cable to take liquid away from the motor connection. If possible, provide a protective cover to protect the motor housing shaft seal and its connections from foreign matter or liquid contamination. The shaft seal is easy to wear and needs regular inspection and replacement. According to the service condition, it is recommended to replace it once a month, but not more than months. For more information, refer to the shaft seal kit on page. Regularly check the motor and seals for damage or wear. If damage or excessive wear is found, replace the component. The brake option on this servomotor is a spring set to hold the brake, which releases when voltage is applied to the brake coil. Separate power is required to disengage the brake. The power supply can be applied through servo motor controller or manual operator control.
