MVME162-522工業卡件
電機制動電路中的電弧抑制驅動器具有包括電弧抑制器的制動控制繼電器。在這種情況下，不需要客戶提供的電弧抑制，除非制動器的功耗需要外部制動器繼電器。電力電纜內的屏蔽信號線兩條整體電力電纜屏蔽回路信號屏蔽兩條中的一條至總體電力電纜屏蔽工廠提供的現場修改驗證驅動器上的電源電纜接地夾是否接觸所有三個電纜屏蔽。直流電源客戶提供的部件制動繼電器二極管或電弧抑制器系列低慣量無刷伺服電機，具有或更小的框架尺寸年月安裝電機系列電機包括用于將電機對準機器的安裝導向器。優選的緊固件為不銹鋼。安裝必須符合所有當?shù)胤ㄒ?guī)，并使用促進安全和電磁兼容性的設備和安裝實踐。更改連接器方向您可以將連接器外殼旋轉。這使您可以將連接器調整到最佳位置，以保護連接免受可能的環境污染，同時提供電纜接入。圓形連接器外殼可沿任一方向旋轉。按照以下步驟旋轉連接器。在饋線上安裝一根配套電纜并將其完全固定或動力制動接頭。用手抓住配合的連接器和電纜插頭，并將其緩慢旋轉至電機外部。對另一個接頭重復這些步驟。注意如果通電，未安裝的電機斷開的機械聯軸器松脫的軸鍵和斷開的電纜是危險的。鎖定并標記拆卸的設備限制電源。向電機通電前，取下軸鍵和其他可能從軸上拋出的機械聯軸器。注意確保電纜已安裝并受到約束，以防止電纜連接處的不均勻張力或彎曲。當電纜彎曲時，電纜上過大且不均勻的橫向力會抑制環境密封。The arc suppression driver in the motor brake circuit has a brake control relay including an arc suppressor. In this case, the arc suppression provided by the customer is not required, unless the power consumption of the brake requires an external brake relay. Shielded signal line in the power cable One of the two overall power cable shielded loop signal shields goes to the on-site modification provided by the overall power cable shield factory to verify whether the power cable grounding clip on the drive contacts all three cable shields. DC Power Customer Supplied Components Brake Relay Diode or Arc Suppressor Series Low Inertia Brushless Servo Motor, with or less frame size Year Month Mounting Motor Series Motors include mounting guides for aligning the motor to the machine. The preferred fastener is stainless steel. The installation must comply with all local regulations and use equipment and installation practices that promote safety and electromagnetic compatibility. Changing the connector orientation allows you to rotate the connector housing. This allows you to adjust the connector to the optimal position to protect the connection from possible environmental pollution while providing cable access. The circular connector housing can be rotated in either direction. Follow these steps to rotate the connector. Install a matching cable on the feeder and fix it completely or power brake connector. Grasp the mating connector and cable plug by hand and slowly rotate them to the outside of the motor. Repeat these steps for the other connector. Note that if the motor is powered on, the loose shaft keys and the disconnected cables of the disconnected mechanical coupling of the unmounted motor are dangerous. Lock and mark the removed device to limit power supply. Before energizing the motor, remove the shaft key and other mechanical couplings that may be thrown from the shaft. Care shall be taken to ensure that cables are installed and restrained to prevent uneven tension or bending at cable connections. When the cable is bent, excessive and uneven lateral forces on the cable will inhibit environmental sealing.
