MVME162-520A系統備件,工業備件
如果使用螺紋電纜插頭，安裝形圈。接頭上的形圈是實現最大環境等級所必需的。如果使用電纜插頭，請勿安裝形圈。在電纜中形成滴水環見第頁。注意在將電纜連接或斷開電機之前，必須關閉伺服驅動電源，如果電纜在電機端斷開，也必須關閉。如果在伺服驅動器通電時連接或斷開饋線電源或制動電纜，可能會發生電弧或意外運動。注意確保電纜已安裝并受到約束，以防止電纜連接器處的不均勻張力或彎曲。在整個電纜敷設過程中，每隔米英尺提供支撐。當電纜彎曲或電線在電纜壓蓋處分離時，電纜連接器處的過度和不均勻橫向力可能導致連接器的環境密封打開和關閉。電機連接器不要在電機連接器上安裝形圈螺紋電纜插頭標準反饋和電源電纜連續撓性饋電和動力制動電纜使用螺紋電纜插頭時，請在馬達連接器上安裝形圈。確認形圈沒有損壞，沒有扭曲，并位于接頭后部附近的凹槽中。電纜插頭預留槽使用電纜插頭時，請勿在就緒電機連接器上安裝形圈。電纜插頭標準和連續柔性反饋電纜標準以及連續柔性動力制動電纜就緒電機連接器系列或更小框架尺寸的低慣量無刷伺服電機年月日。小心地將反饋或動力制動電纜插頭如圖所示上的平面與電機接頭上的平面對齊。用手擰緊插頭上的套環，使其完全固定在連接器上螺紋電纜插頭需要旋轉五到六圈。電纜插頭需要大約四分之一轉。將電纜插頭與電機接頭配合時，不要用力過猛。如果插頭和連接器不能用輕微的手用力連接在一起，請重新對齊平面并重試。重要事項所示電機方向用于清楚顯示每個電纜插座上的對準標記。安裝時建議的電機方向?qū)⒔宇^定位在電機底部。提示完全固定的螺紋插頭在連接器和插頭之間留下約的小開口。注意對齊鍵控連接器并手動擰緊建議的圈數。
If a threaded cable plug is used, install the O-ring. The O-rings on the connector are necessary to achieve the maximum environmental rating. If a cable plug is used, do not install the O-ring. Form a drip loop in the cable, see page. Note that before connecting or disconnecting the cable to the motor, the servo drive power must be turned off. If the cable is disconnected at the motor end, it must also be turned off. If the feeder power supply or brake cable is connected or disconnected when the servo drive is powered on, arcing or unexpected movement may occur. Take care to ensure that the cable is installed and restrained to prevent uneven tension or bending at the cable connector. Support shall be provided every meter foot throughout the cable laying process. When the cable is bent or the wires are separated at the cable gland, excessive and uneven lateral forces at the cable connector may cause the environmental seal of the connector to open and close. Motor connector Do not install ring screw cable plug on motor connector Standard feedback and power cable Continuous flexible feeding and power brake cable When using screw cable plug, please install ring on motor connector. Verify that the O-ring is not damaged, twisted, and located in the groove near the rear of the connector. When using the cable plug in the cable plug preparation slot, do not install the O-ring on the ready motor connector. Cable plug standard, continuous flexible feedback cable standard and continuous flexible power brake cable Ready motor connector series or lower frame size low inertia brushless servo motor Year Month Day. Carefully align the plane on the feedback or power brake cable plug as shown in the figure with the plane on the motor connector. Tighten the collar on the plug by hand to fully secure it to the connector The threaded cable plug needs to be rotated five to six turns. The cable plug takes about a quarter turn. Do not use excessive force when fitting the cable plug with the motor connector. If the plug and connector cannot be connected together with slight hand force, realign the plane and try again. IMPORTANT The motor orientation shown is used to clearly show the alignment marks on each cable socket. The recommended motor direction during installation locates the connector at the bottom of the motor. Prompt that a fully secured threaded plug leaves approximately a small opening between the connector and the plug. Note the alignment of the keyed connector and hand tighten the recommended number of turns.
