MVME162-513A系統模塊卡件
如果無法擰緊連接器，請驗證鍵控連接器是否正確對齊。不要使用工具例如鉗子和虎鉗擰緊接頭。制動器和電源連接器反饋連接器對齊平面對齊平面系列或更小框架尺寸的低慣量無刷伺服電機年月產品尺寸本節提供了電機的尺寸。見詳圖±±軸直徑公差電機，電機?詳圖軸直徑和電機?連接器反饋連接器直徑螺栓圓上的直徑孔尺寸單位為軸端螺紋孔電機螺紋螺紋深度，電機螺紋螺紋深度連接器外殼可在導向直徑公差范圍內旋轉電機?電機，鍵系列低慣量無刷伺服電機，具有或更小的框架尺寸年月和電機尺寸電機設計為公制尺寸。英寸尺寸是毫米的近似換算。無公差的尺寸僅供參考。電機類別。編號如果訂購帶制動器的或電機，則在尺寸和上增加在和上增加如果訂購帶制動器的或電機，則尺寸和增加和增加此尺寸的公差為±±鍵槽軸直徑和導向直徑公差見第頁。。毫米英寸毫米英寸。公差和補充尺寸電機負載力額定值電機能夠在持續的軸負載下運行。圖中顯示了徑向和軸向負載力的位置，并列出了最大值。載荷以磅千克為單位進行測量，這是數學轉換。軸上的負載力下表表示了各種負載和速度下的小時軸承疲勞壽命。這小時的使用壽命沒有考慮到因軸承磨損可能導致的特定應用壽命減少來自外部的油脂污染。和鍵槽公差軸跳動導向偏心度最大端面跳動鍵槽深度鍵槽寬度徑向負載力額定值電機類別。編號，最大速度磅軸向負載力徑向負載力施加在軸延伸中心。系列或更小框架尺寸的低慣量無刷伺服電機年月軸向負載力額定值最大徑向負載電機類別。編號，最大速度電機類別。轉/分轉/分轉/分轉/分，最大速度磅系列或更小框架尺寸的低慣量無刷伺服電機年月連接器數據本表提供了連接器上的反饋電源和制動引腳的信號說明。
If the connector cannot be tightened, verify that the keyed connector is properly aligned. Do not use tools such as pliers and vises to tighten the connector. Brake and power connector feedback connector alignment plane alignment plane series or lower frame size low inertia brushless servo motor monthly product size This section provides the motor size. See the detail drawing ± ± axis diameter tolerance motor. The motor shaft diameter and motor connector feedback connector diameter. The diameter hole size on the bolt circle is the shaft end threaded hole. The motor thread thread depth. The connector shell can rotate the motor within the guide diameter tolerance. The key series low inertia brushless servo motor has or smaller frame size. The motor is designed as metric size. Inch dimensions are approximate conversions of millimeters. Dimensions without tolerances are for reference only. Motor category. No. If ordering a braked or motor, add dimensions and to add dimensions and If ordering a braked or motor, the tolerance for dimensions and adding and adding this dimension is ± ± the tolerance for keyway shaft diameter and guide diameter see page.. Millimeters inches millimeters inches. Tolerances and supplementary dimensions Motor load force ratings The motor is capable of operating under continuous axle load. The figure shows the location of the radial and axial load forces and lists the maximum values. The load is measured in pounds and kilograms, which is a mathematical conversion. The following table shows the hourly bearing fatigue life under various loads and speeds. The service life of this hour does not take into account the specific service life that may be reduced due to bearing wear from external grease contamination. And keyway tolerance shaft runout pilot eccentricity maximum end face runout keyway depth keyway width radial load force rating motor category. No., maximum speed pounds axial load force radial load force is applied to the shaft extension center. Series or smaller frame size low inertia brushless servo motor Monthly axial load force rating Maximum radial load motor category. Number, maximum speed motor category. Revolution/minute revolution/minute revolution/minute revolution/minute revolution/minute, maximum speed pounds series or lower frame size low inertia brushless servo motor monthly connector data This table provides the signal description of the feedback power supply and brake pin on the connector.
