MVME162-512A工業卡件
反饋和引腳描述引腳高分辨率編碼器高分辨率編碼器增量編碼器引腳和相功率相位和功率相位也可以分別標記為和。相相接地數據數據保留數據數據保留保留保留保留公共公共連接器保留保留公共保留保留反饋連接器系列或更小框架尺寸的低慣量無刷伺服電機年月拆除和安裝軸鍵軸鍵由鋼制成。指定的公差為安全和剛性連接提供過盈配合略大于開口。要取下軸鍵，請執行以下操作之一用鉗子或類似工具抓住鍵，將其抬起。將螺絲刀插入鑰匙和插槽之間，撬起鑰匙。要安裝軸鍵，請執行以下步驟。在繼續操作之前，確認替換鍵與軸中的鍵槽和匹配的機械連接例如，聯軸器或滑輪相匹配。將鍵的前部與電機軸的前部對齊。這可防止鍵槽電機端的弧形切割端干擾鍵的正確定位。用夾具支撐軸直徑的下側，并使用受控的按壓裝置在頂面施加恒定的力，將鍵壓入軸中。軸鍵安裝注意事項安裝或拆卸軸鍵時，不要用工具敲擊電機的軸聯軸器或滑輪。如果在安裝聯軸器和皮帶輪或拆除軸鍵時對軸施加劇烈沖擊，或者從電機安裝面施加杠桿以拆除安裝在電機軸上的裝置，則可能會損壞電機軸承和反饋裝置。用車輪拉拔器向軸的用戶端施加恒定壓力，以移除摩擦配合或卡住的裝置。用于電機支架的鍵槽鍵軸支架的鍵對齊徑向切口系列低慣量無刷伺服電機，具有或更小的框架尺寸年月電機電纜和附件套件本節介紹了系列低慣性電機可用的附件。電機電纜工廠制造的反饋電纜和電力電纜有標準電纜長度。它們提供了實現環境等級和屏蔽端接所需的密封。有關可用電纜的完整列表請聯系最近的銷售辦事處或參考運動配件規格技術數據。軸封套件軸封是一種屏障，可以防止水分和顆粒進入電機軸承。軸封容易磨損，需要定期檢查和更換。根據使用情況，建議每個月更換一次，但不超過個月。表中列出了電機的目錄號和相應的更換丁腈軸密封套件。有關如何安裝軸封的說明，請參閱軸封套件安裝說明。重要事項軸封必須潤滑。潤滑劑隨軸封套件提供。第三方軸封不允許與這些電機一起使用。
Feedback and pin description pins High resolution encoder High resolution encoder Incremental encoder pin and phase power phase and power phase can also be marked as and respectively. Phase grounding data data retention data retention retention retention retention public public connector retention retention public retention retention feedback connector series or smaller frame size low inertia brushless servo motor year month remove and install shaft key shaft key made of steel. The specified tolerance provides an interference fit slightly greater than the opening for safe and rigid connections. To remove the shaft key, do one of the following to grasp the key with pliers or a similar tool and lift it. Insert a screwdriver between the key and the slot and pry up the key. To install the shaft key, perform the following steps. Before continuing, confirm that the replacement key matches the keyway in the shaft and the matching mechanical connection, such as coupling or pulley. Align the front of the key with the front of the motor shaft. This prevents the arc-shaped cutting end of the motor end of the keyway from interfering with the correct positioning of the key. Use a jig to support the lower side of the shaft diameter, and use a controlled press device to apply a constant force on the top surface to press the key into the shaft. Precautions for shaft key installation When installing or removing the shaft key, do not use tools to knock the shaft coupling or pulley of the motor. The motor bearing and feedback device may be damaged if severe impact is exerted on the shaft when installing the coupling and pulley or removing the shaft key, or lever is applied from the motor mounting surface to remove the device installed on the motor shaft. Use a wheel puller to apply constant pressure to the user end of the shaft to remove friction fits or stuck devices. Keyway for motor support Keyway for key shaft support Key alignment Radial notch series low inertia brushless servo motor with or less frame size Year motor cable and accessory kit This section describes the accessories available for series low inertia motors. The feedback cable and power cable manufactured by the motor cable factory have standard cable lengths. They provide the seals required to achieve environmental ratings and shield terminations. For a complete list of available cables, contact the nearest sales office or refer to the sports accessory specifications technical data. Shaft seal kit The shaft seal is a barrier that prevents moisture and particles from entering the motor bearings. The shaft seal is easy to wear and needs regular inspection and replacement. According to the service condition, it is recommended to replace it once a month, but not more than months. Table lists the catalog number of the motor and the corresponding replacement nitrile shaft seal kit. For instructions on how to install the shaft seal, refer to the shaft seal kit installation instructions. Important The shaft seal must be lubricated. Lubricant is supplied with the shaft seal kit. Third party shaft seals are not allowed to be used with these motors.
