MVME162-10備件模塊
對連接到控制單元的每個墊重復該過程，檢查相應的通道故障變?yōu)榧t色。注意通道故障狀態指示單個墊的操作或故障。控制單元操作模式自動復位通電電源自動復位和機器啟用亮起。當墊子工作時機器啟用的熄滅備用墊子機器啟用點亮手動重置通電電源手動重置和機器啟用亮起。按下重置按鈕機器啟用的在墊子運行時亮起機器啟用熄滅墊機器啟用發光二極管仍熄滅按下重置按鈕，機器啟用亮起在故障情況下，機器啟用的燈熄滅，在故障排除之前不允許重置。在故障狀態下，如果有墊子故障，一個或多個墊子狀態將點亮。在開路或短路情況下，將亮起紅色。如果存在故障，且均未亮起，則說明控制單元故障。檢查安全功能單通道系統參見圖和第節模擬正常操作。站在墊子上啟動墊子，并檢查主接觸器是否立即脫落。檢查任何其他與安全相關的停止功能，如制動器離合器接觸器是否按預期運行。雙通道系統見圖和第節模擬正常操作。站在墊子上啟動墊子，并立即檢查兩個最終接觸器是否脫落。檢查任何其他安全相關的停止功能，如制動離合器接觸器是否按預期運行。隔離電源，然后通過將端子塊處的端子和短路來安裝臨時故障圖或?；謴?fù)電源并啟動傳感器墊，并檢查其中一個最終接觸器是否立即斷開，以及與該通道相關的任何其他停止功能是否按預期運行。檢查控制單元不會復位隔離電源并排除臨時故障?；謴?fù)電源并檢查墊子系統是否正常工作。采取相同的電氣安全預防措施，在端子塊的端子和之間臨時短路，重復測試圖或。再次檢查控制單元將不會復位拆除臨時故障檢查墊系統。所有系統類型進行所需的任何其他測試，以確認安全相關控制系統符合規定的類別要求，并按預期工作。檢查與受墊系統安裝影響的機器電路相關的任何其他安全功能。這些測試應有現有程序。在電源處隔離機器電源。重新連接機器控制系統提供的任何自動復位功能。將機器原動機重新連接至最終接觸器。固定所有蓋子和門。功能檢查恢復機器電源。檢查。在重置墊子控制單元之前，機器無法開始操作。
Repeat the process for each pad connected to the control unit and check that the corresponding channel fault turns red. Note that the channel fault status indicates the operation or fault of a single pad. Automatic reset of control unit operation mode Automatic reset of power supply and machine enabling light up. The machine is enabled when the mat is working. The standby mat is enabled. The machine is enabled. The manual reset is on. The power is on. The manual reset and the machine is enabled are on. Press the reset button. If the machine is enabled, it will light up while the mat is running. If the machine is enabled and the LED is still off, press the reset button. If the machine is enabled and lit up, the light that the machine is enabled will go out. Resetting is not allowed until the fault is eliminated. In the fault state, if there is a mat fault, one or more mat states will light up. In case of open circuit or short circuit, it will light red. If there is a fault and none of them light up, the control unit is faulty. Check the safety function of the single channel system. Refer to Figure and Section to simulate normal operation. Stand on the mat and start the mat, and check whether the main contactor falls off immediately. Check that any other safety related stop functions, such as the brake clutch contactor, operate as expected. The dual channel system is shown in Figure and Section to simulate normal operation. Stand on the mat and start the mat, and immediately check whether the two final contactors fall off. Check whether any other safety related stop functions, such as brake clutch contactor, operate as expected. Isolate the power supply and then install a temporary fault diagram or by short circuiting the terminals at the terminal block. Restore the power supply and start the sensor pad and check that one of the final contactors is immediately disconnected and that any other stop functions associated with that channel are operating as expected. Check that the control unit will not reset the isolated power supply and eliminate temporary faults. Restore the power supply and check whether the mat subsystem works normally. Take the same electrical safety precautions, temporarily short circuit between terminals and of the terminal block, and repeat the test diagram or. Checking the control unit again will not reset the temporary fault check pad system. Carry out any other tests required for all system types to confirm that the safety related control system meets the specified category requirements and works as expected. Check for any other safety functions related to the machine circuits that are affected by the installation of the mat system. These tests should have existing procedures. Isolate the power supply of the machine at the power supply. Reconnect any automatic reset functions provided by the machine control system. Reconnect the machine prime mover to the final contactor. Secure all covers and doors. Function check to restore machine power. Check. The machine cannot start operation until the mat control unit is reset.
